Paradyne FrameSaver 9120 User Manual Download Page 53

Page: 53 / 82

Displaying System Information

4-27

9121-A2-GB20-20

May 1998

Statistic

What It Indicates

Unknown DLCI

Number of frames received over the interface that were
addressed to unknown DLCIs.

The DLCI may not have been configured, or it has been
configured to be Inactive.

Indicates that the access units or devices at both or either end
of the circuit have been configured incorrectly.

Unknown Error

Number of frames received over the interface that do not fall
into one of the other statistic categories.

Indicates that the error is not one that the unit can recognize.

Frame Relay LMI

LMI Protocol

LMI protocol configured for the frame relay link.

Normal condition.

Status Msg Received

Number of LMI status messages received over the interface.

Normal condition.

Reliability Errors

Number of LMI reliability errors received over the interface.

Indicates the access unit is not receiving a response to a
status or poll request.

Protocol Errors

Number of protocol errors observed over the interface.

Number of Inactives

Number of times the LMI has declared the frame relay link
Inactive.

Network problems.

Summary of Contents for FrameSaver 9120


















































































Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands

Paradyne FrameSaver 9120, User Manual

Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands