background image

I

MPORTANT INFORMATION

Limitation of liability
It is mandatory for the NEON panel to be installed in ac-

cordance with this manual, applicable codes, and the in-

structions of the Authority Having Jurisdiction. The manu-

facturer shall not under, any circumstances, be liable for 

any incidental or consequential damages arising from loss 

of property, or other damages, or losses owing to the fail-

ure of products beyond the cost of repair, or replacement 

of any defective products. The manufacturer reserves the 

right to make product improvements and change product 

specifications at any time.

The manufacturer assumes no responsibility for errors or 

omissions, whilst every precaution has been taken during 

the preparation of this manual to ensure the accuracy of its 

contents.

Warranty
PARADOX HELLAS warrants its products to be free from 

defect in materials and workmanship under normal use for 

a period of two (2) years (the “Warranty Period”) from the 

production-delivery date, identified by date code(s) indicat

-

ed on the products. Because PARADOX HELLAS does not 

install or connect the products and because the products 

may be used in conjunction with products not manufac-

tured by PARADOX HELLAS, PARADOX HELLAS cannot 

guarantee the performance of the fire alarm system and 

shall not be responsible in any way whatsoever for faulty 

installation or connection.

Declaration of Conformity

Fire  alarm  control  panel  NEON  is  certified  from  EVPU  (Noti

-

fied  body  No.  1293)  according  to  European  Regulation 

CPR 

305/2011

 with certification number Νο.

1293-CPR-0604

 of June 

27, 2018.

-Standards:

EN 54-2: 1997/A1: 2006/AC: 1999

EN 54-4: 1997/A2: 2006/AC: 1999

Certificates can be found online at phsvesis.com.

RoHS directive compliance

The EC RoHS guideline has been released in order to 

reduce the heavy metal load in electrical and electronic 

products caused by e.g. lead and mercury. All manu-

facturers are obligated to provide only RoHS-compliant 

products  to  the  European  market,  effective  from  July 

1st, 2006.

PARADOX HELLAS

 hereby states that the NEON 

panel  is  fully  compliant  with  RoHS  2002/95/EC  direc

-

tive.

Disposal of your old appliance

1.  When  this  crossed-out  wheeled  bin  symbol  is  at

-

tached to a product it means the product is covered by 

the European Directive 2002/96/EC.

2. All electrical and electronic products should be dis-

posed of separately from the municipal waste stream 

via designated collection facilities appointed by the gov-

ernment or the local authorities.

3. The correct disposal of your old appliance will help 

prevent potential negative consequences for the envi-

ronment and human health.
4. For more detailed information about disposal of your 

old  appliance,  please  contact  your  city  office,  waste 

disposal service or the shop where you purchased the 

product.

Summary of Contents for DEVELOPED Neon 2

















Reviews: