manualshive.com logo in svg

Panoramic Power Energy Insight, Installation And Configuration Manual

Share
Download
Panoramic Power Energy Insight Installation And Configuration Manual Download Page 8

 

 

 

 
 

8 

 

Bridge installation and configuration guide 

January 2018 
© 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. 
Registered in England & Wales No 3033654

 

 

Prerequisites 

•

 

An Ethernet cable for configuring the bridge. 

•

 

An Ethernet cable if you connect to the Internet via wired LAN. 

•

 

A SIM card if you connect to the Internet via a standard GSM network. 

Connecting Pulse Inputs 

You can connect the bridge to a KY or KYZ pulse output of a meter. 

How to Proceed 

1.

 

Screw the pulse wires into the adapter connected to the pulse input. Make sure to screw the K wire into 
the K input, and either the Y or Z wire into the Y input. 

2.

 

Plug the adapter into one of the pulse inputs on the side of the bridge. 
 

 

 
DC specification 

•

 

Maximum current (at K-Y short): 0.9 mA 

•

 

Internal pullup voltage: 5 VDC 

•

 

Absolute maximum K-Y voltage input range: 0-26 VDC 

Summary of Contents for Energy Insight


























Reviews:

No comments

Brands by name

Popular brands

Load more brands