manualshive.com logo in svg

Panoramic Power Energy Insight, Installation And Configuration Manual

Share
Download
Panoramic Power Energy Insight Installation And Configuration Manual Download Page 6

 

 

 

 
 

6 

 

Bridge installation and configuration guide 

January 2018 
© 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. 
Registered in England & Wales No 3033654

 

Unpacking the Hardware 

We recommend that you follow these unpacking instructions before installing the hardware. 

How to Proceed 

1.

 

Check the box. If any damage occurred during shipment, contact your sales representative. 

2.

 

Open the box. It should include the following items: 

•

 

Bridge 

•

 

Cellular antenna 

•

 

RF antenna, labeled 

Rx-1

 (Europe) or 

Rx-2

 (USA)  

•

 

Pluggable adapters for the pulse inputs 

•

 

Pluggable adapter for the Modbus input 

•

 

DIN rail adapter with mounting screws 

•

 

5V DC wall adapter 

•

 

4-piece reclose able fastener with adhesive 

3.

 

Keep the box in case you need to repack the bridge later. 

Attaching the Antennas 

Before performing any connections, mount the antennas onto the bridge as follows: 

 

1.

 

(European model) Screw the RF antenna labeled 

Rx-1

 into the connector marked 

Rx-1

, as shown below.  

 

(US model) Screw the RF antenna labeled 

Rx-2

 into the connector marked 

Rx-2

. 

2.

 

Screw the cellular antenna into its connector. 

3.

 

Position the antennas as shown below. 

Summary of Contents for Energy Insight


























Reviews:

No comments

Brands by name

Popular brands

Load more brands