PanelClaw Polar Bear III HD 5 Degree Installation Manual Download Page 24

Page: 24 / 27

Polar Bear III HD 5 Degree Installation Manual
9910034 Rev F

To DC

Grounding Path

Ground Lug
Tyco #2106831-1

Racking Ground Connection Detail

Racking Ground

To Adjacent
Ballast Tray

Module Ground

Typical: East-West Module to Racking to Module Bonding Path

Ground Path

through Support

Typical: North-South Module to Module

Bonding Path

Connect ballast trays to modules
using a single continuous solid
copper wire per row. See
instructions for copper sizing

Ballast trays on south row do not
need to be bonded together since
they are bonded to the northern
trays thru the Tray-Support-Claw-
Support-Tray bonding path.

Figure 16 Bonding and Grounding Instructions

Module Ground Connection Detail

Summary of Contents for Polar Bear III HD 5 Degree




























Search results

Summary of Contents for Polar Bear III HD 5 Degree

Reviews:

Related manuals for Polar Bear III HD 5 Degree

Brands by name

Popular brands

PanelClaw Polar Bear III HD 5 Degree, Installation Manual

Search results

Summary of Contents for Polar Bear III HD 5 Degree

Reviews:

Related manuals for Polar Bear III HD 5 Degree

Brands by name

Popular brands