manualshive.com logo in svg

Panduit ATLONA AT-HDR-CAT-2, Manual

Share
Download
Panduit ATLONA AT-HDR-CAT-2 Manual Download Page 41

AT-HDR-CAT-2

41

Configuration and Management Interfaces

RS-232 Parameter Setting

 

Click each of these drop-down boxes to select the desired baud rate, data bits, parity bit, and stop bit for the 

MASTER RS-232 / IR

 port.

Setting

Description

Baud rate

Sets the baud rate.  The following options are available: 2400, 9600, 19200, 38400, 

56000, 57600, 115200.

Data bit

Sets the number of data bits used to represent each character of data.  The following 

options are available:  7 or 8.

Parity

Sets the parity bit, which can be included with each character to detect errors during 

the transmission of data.  The following options are available:  None, Odd, or Even.

Stop bit

Sets the stop bit.  Stop bits are sent at the end of each character, allowing the client to 

detect the end of a character stream.  The following options are available:  1 or 2.

RS-232 page

RS-232

Summary of Contents for ATLONA AT-HDR-CAT-2























































Reviews:

No comments

Brands by name

Popular brands

Load more brands