Level 1
Recording remote controls (D800/
D670/D030/R465)/radio tags (BT760)
Changing the factory preset
of the service PIN-code
Recording the idle speed (rpm)
to the system memory
Resetting to the factory settings
Recording a Bluetooth engine
compartment module (RHM-03BT)
Recording Bluetooth radio
relays №1, №2 (BTR-101)
Recording a Bluetooth GPS/GLONASS
receiver (NAV-035BT)
Programming and configuring
an “Immobilizer PIN-code”
Emergency deactivating immobilizer
radio tags
Updating firmware of the built-in
Bluetooth modem
Programming bypass of an original
immobilizer
Pairing and unpairing a mobile device
Updating firmware of radio
relays №1, №2 (BTR-101)
Updating firmware of an engine
compartment module (RHM-03BT)
Updating firmware of a GPS/GLONASS
receiver (NAV-035BT)
Recording door sensors №1, №2
(DMS-100BT)
Updating firmware of door
sensors №1, №2 (DMS-100BT)
Recording additional modules
(DI-04, BT-01)
Updating firmware of additional
modules (DI-04/BT-01)
Level 2
Level 3
Level 4
Level 5
Level 6, 7
Level 8
Level 11
Level 15
Level 16
Level 17
Level 18
Level 19, 20
Level 21
Level 22
Level 23, 24
Level 25, 26
Level 27
Level 28
Level 23,24 – Recording door sensors №1, №2 (DMS-100BT)
• Insert a battery in the sensor.
• The system will confirm recording of the sensor to the system
memory with 1 beep of the siren.
Level 27 – Recording additional modules (DI-04, BT-01)
Recording a radio module (DI-04):
• Connect power supply of the module.
• Press and hold the “VALET DI” button for 6 seconds. Release the
button after the sixth flash of the “LED DI”.
• The system will confirm recording of the module to the system
memory with 1 beep of the siren.
Recording a radio relay (BT-01):
• Connect the wire 5 (“Ground”) to a grounded spot of a car.
• Apply +12V to the wire 1 (“+12V Power supply of the relay”).
• The system will confirm recording of the module to the system
memory with 1 beep of the siren.
EXAMPLES OF RECORDING ADDITIONAL DEVICES
WARNING!
The additional devices that are included in the
system set have been already recorded in the system memory
(see the “System set” section of the user manual).
To record additional devices, enter a required level of the
programming menu. Perform a recording procedure in accordance
with a device manual. To save the recorded device, press the VALET
button once. The series of red and green flashes of the LED indicator
will confirm saving.
Level 1 – Recording remote controls and radio tags
Recording remote controls (D800/D670/D030/R465):
Press and hold three buttons of a remote control (arm/disarm/F)
simultaneously for 1 second (until a short beep from the main
remote control or until fading a LED of an additional remote control),
then release the buttons. If recording was successful, the main
remote control will emit 2 short beeps and a siren of the base unit
will emit 1 beep. After this you can move to recording the next
remote control or radio tag.
Recording a radio tag (BT760):
Press the control button on a tag and hold it for 6 seconds (6 flashes
of the tag status indicator), release the button after the sixth flash. If
the recording was successful, a siren will emit 1 beep, after this
you can move to recording the next tag.
Level 5 – Recording a Bluetooth engine compartment module
(RHM-03 BT)
• Connect the wire 4 (“LIN output/Programming”) and wire 5
(“Ground”). Connect them to a grounded spot of a car.
• Apply +12V to the wire 7 (“+12V Power supply of the module”).
• The system will confirm recording of the module to the system
memory with 1 beep of the siren.
• Disconnect the wire 4 (“LIN output/Programming”) from the wire 5
and insulate it.
Level 6, 7 – Recording Bluetooth radio relays №1, №2 (BTR-101)
• Connect the wire 1 (“Ground”) to a grounded spot of a car.
• Connect the wire 3 (“Programming”) and wire 4 (“+12V Power
supply of the radio relay”). Connect them to +12V.
• The system will confirm recording of the radio relay to the system
memory with 1 beep of the siren.
• Disconnect the wire 3 (“LIN output/Programming”) from the wire 4
and insulate it.
Level 8 – Recording a Bluetooth GPS/GLONASS receiver
(NAV-035BT)
• Connect the wire 2 (“Ground”) to a grounded spot of a car.
• Apply +12V to the wire 1 (“+12V Power supply of the receiver”).
• The system will confirm recording of the receiver to the system
memory with 1 beep of the siren.
Level 18 – Pairing and unpairing a mobile device
Pairing mobile device:
The LED indicator will light green after entering the level. Open the
mobile application, press the “Search device” button. The application
will search for the system via Bluetooth connection. Select the found
system, the system and the mobile device will be automatically
paired. The system will confirm pairing with a sound signal of the
siren and a red light of the LED indicator.
Unpairing mobile device:
The LED indicator will light red after entering the level. Press the
VALET button and hold it for more than 4 seconds, release the
button. The system will confirm deleting with the series of sound
signals of the siren and the system will return to mobile device
registration mode (the LED indicator will light green).
GSM Antenna
micro-USB
SIM 2 SIM 1
VALET
button
Fuse of the XP9
socket
(5А)
XP6
XP1
XP3
XP3
XP2
XP6
XP8
XP7
XP9
XP10
White
2
IMMO-KEY2 OUT
IMMO-KEY1 IN
IMMO-KEY2 IN
Black
3
Red
4
IMMO-KEY1 OUT
Green
1
External VALET button
XР2
Temperature
sensor
DS18B20
XP7
(+)
(-)
CAN2-L
CAN2-H
CAN2
CAN1-L
CAN1-H
CAN1
CH8
- Output "Closing the central lock"
200mA (-)
INP9 - Input "Ignition"
INP5
- Input "Front hood"
200 mA (-)
200 mA (-)
200mA (-)
СН6 -
Output "Opening the central lock"
CH10
- Output "N.O. blocking"
6
7
8
9
10
1
2
3
4
5
4
Green/Black
3
Yellow
2
Yellow/White
1
Orange/White
5
Green/Blue
6
Orange/Black
7
Yellow/Black
8
Brown/White
9
Blue/Black
10
Blue
CH12
- Output "Turn indicators"
To original
wires
9
10
11
12
13
14
15
16
СН13 -
Output "Blocking original radio channel"
СН15
- Output "Comfort (closing windows)"
200mA (-)
200mA (-)
200mA (-)
200mA (-)
(-)
СН16 -
Output "Switching off ACC (simulation of opening a door)"
200mA (-)
СН3/
INP7
-
Output "Ignition 1"
INP4/
СН1
- Input "Doors"
INP6/
СН7
- Input "Trunk"
200mA (-)
СН4/
INP3
-
Output "Beeper"
INP8 -
Input "Neutral/Handbrake"
INP2 -
Input "Brake pedal"
INP1-
Input "Fuel level"
Input "Tachometer"
LIN1
- Input "Reading and control a car"
LIN2
- "Webasto/Eberspaecher"
LIN1
- Output "Reading and control a car"
200mA (-)
(+)
(+)
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Green/Orange
Orange/Blue
White/Blue
White/Green
Brown/Yellow
Brown
Pink
Black
Gray/White
White
Brown/Black
Red/Black
Green
Yellow/White
Black/White
1
2
3
4
5
6
7
8
CAN3-L
(see the back side)
CAN3
(-)
+12V
Gray/Black
2A(+)
2A(+)
2A(+)
CH18
- Output "Turn indicators"
CH20
- Output "Video Recorder"
2A(+)
CH17
- Output "Radar detector"
XP9
CH
19
- Output "Siren"
Total current of the channels CH17, CH18, CH19, CH20 cannot be more than 5A
1
Gray/Red
2
Gray/Black
3
Black
4
Gray
5
Purple
6
Red
3
2
1
6
5
4
LED
GSM
2.4 GH
z
A
nt
enna
868 MH
z
A
nt
enna
M
icr
ophone
GPS/GL
ONASS
A
nt
enna
Connection
of additional
temperature
sensors
Dallas Semiconductor DS 18B20
GND
DQ
+5V
model: PROFESSIONAL v2
WIRING DIAGRAM
Programming menu
WARNING!
Before starting the installation of the system,
choose a car model in the ALARM STUDIO (CAN-bus protocol).
WARNING!
A SIM card must only be inserted while the system
is not powered.
WARNING!
All power circuits of additional devices that are not
powered through the base unit of the system should have
their own fuses.
WARNING!
The security system does not require regular
maintenance. In case of malfunction it should be taken to a
specialized service center.
WARNING!
Do not shield the built-in antennas.
IT IS FORBIDEN
to install the system on a car with
normal voltage other than 12V.
IT IS FORBIDEN
to bypass original fuses of a
security system in the installation process.
IT IS FORBIDEN
to install the security system with
damaged output cables.
Warning!
XP3 is a multifunctional IMMO-KEY port. It is used only for
bypass of an original immobilizer. It connects in accordance with an
installation manual from the Pandora Alarm Studio.
+ 12V
CH2
Ignition
CH14
Starter
CH11
Bypass
CH9
N.O. Blocking
CH5
АСС
Brake pedal*
XP8
3
2
1
Relay module RMD-5M
6
5
4
1
4
2
5
3
6
** Total current of the relays R3+R4+R5
cannot be more than 40A
* For remote engine start implementation
with the "Start/Stop button" logic
40А
R4
R5
R3
R2
R1
R1
R2
R3
R4
R5
20A
**
20A
**
20A
**
20A
20A
Brown
Yellow
Orange
Green/Red
Blue/Red
Blue
Blue/Black
Green
Green/Black
Red
Relay
module
Red
Brown
Yellow
Orange
Green
Blue
(–)
(–)
(–)
(–)
(–)
(+)
