Pandora Mini Moto, User And Installation Manual, Page: 7 / 23

13
12
U S E R A N D I N S TA L L AT I O N MA N UA L PA N D O R A M I N I M OTO
Immobiliser mode
This mode is used to recognize an owner using authorization devices when the system is disarmed.
When turning on the ignition, the base unit performs a search for authorization devices in the radio
coverage zone. If there is no any authorization device in the radio coverage zone, the system will block
the engine. Engine blocking will occur immediately or at the time a motion sensor detects movement,
it depends on the system settings. When an authorization device appears in the coverage zone, the
system will exit blocking mode and will continue to work in normal mode.
!
T
his mOdE is disablEd by dEfaulT
. T
hE cONfiguraTiON shOuld bE madE by a qualifiEd TEchNiciaN
.
f
Or EmErgENcy disarmiNg sEE
«c
ONTrOl ThE sysTEm iN casE Of EmErgENcy
». E
NgiNE blOckiNg whilE driviNg pOsEs aN
iNcrEasEd risk
. w
E sTrONgly rEcOmmENd ThaT yOu bE parTicularly carEful whEN usiNg This mEThOd Of blOckiNg
.
Anti-Hi-Jack mode
The Anti-Hi-Jack mode helps to prevent aggressive seizure of a vehicle in case of disappearance
of the authorization devices from the radio coverage zone when system is disarmed and ignition is
on. If the system cannot detect an authorization device, the base unit will perform a delayed engine
blocking. The siren will play the ‘Engine blocking warning’ ringtone before blocking. The engine will
be blocked immediately or at the time the vehicle starts moving, it depends on the system settings.
When an authorization device appears in the coverage zone, the system will exit blocking mode and
will continue to work in normal mode.
!
T
his mOdE is disablEd by dEfaulT
. T
hE cONfiguraTiON shOuld bE madE by a qualifiEd TEchNiciaN
.
f
Or EmErgENcy disarmiNg sEE
«c
ONTrOl ThE sysTEm iN casE Of EmErgENcy
». E
NgiNE blOckiNg whilE driviNg pOsEs aN
iNcrEasEd risk
. w
E sTrONgly rEcOmmENd ThaT yOu bE parTicularly carEful whEN usiNg This mEThOd Of blOckiNg
.
Code Immobiliser (pin-to-drive) function
This function allows to use the pre-programmed «Immobiliser PIN-code» to disable the engine blocking,
service mode, disarming the security system. The code must be entered using original vehicle controls
(buttons/lever/pedal) and/or additionally installed elements.
AN EXAMPLE OF USING THE FUNCTION
• Turn on the ignition to disable engine blocking or service mode, turning on the ignition is not required if
you want to disarm the system or control time channels.
• Enter the «Immobiliser PIN-code», code can consist max of 4 digits from 1 to 9.
- Press the pre-programmed button/lever/pedal the number of times equals to the first digit.
- Pauses between presses should not exceed 1 second. More than 1 second pause will be interpreted
as the start of the next digit input.
• After entering the code correctly, the system will perform the programmed function.
!
T
his mOdE is disablEd by dEfaulT
. T
hE cONfiguraTiON shOuld bE madE by a qualifiEd TEchNiciaN
.
Checking the number of paired devices
The number of paired radio tags/mobile devices can be checked by the number of flashes of the LED
indicator. The number of remotes/tags/mobile device can be checked when switching on the ignition
(system must be disarmed). The number of orange flashes will indicate the number of paired remotes/
bands/watches, the number of green flashes will indicate the number of paired radio tags, a following
red flash will indicate a paired mobile device.
You can also check the number of paired radio tags/mobile devices by taking off and putting back on
battery terminal. The system will emit short sound signals from a siren .