manualshive.com logo in svg

Panasonic WV-X6511N, Operating Instructions Manual, Page: 156 / 265

Share
Download
Panasonic WV-X6511N Operating Instructions Manual Download Page 156

[Panasonic alarm protocol]

Click “Panasonic alarm protocol notification >>” to display the setup menu that can configure the settings
relating to transmitting Panasonic alarm protocol notifications when an alarm occurs. The setup menu will be
displayed in a newly opened window. (

®

page 161)

[HTTP alarm notification]

Click “HTTP alarm notification setup >>” to display the setup menu that can configure the settings relating to
transmitting HTTP alarm notifications when an alarm occurs. The setup menu will be displayed in a newly
opened window. (

®

page 162)

2.7.4.1  Configure the settings relating to Preset per sender (“Preset
per sender” setup menu)

On the [Alarm] tab of the “Alarm” page (

®

Page 153), click “Preset per sender” for “Command alarm”.

The sender’s address for the command alarm, and the preset position for that address can be registered in
this section.

[Sender’s address 1] - [Sender’s address 8]

Set the sender’s IP address for the command alarm, and the preset position for that address. Up to 8 notification
addresses can be set.

[Auto track cooperation] checkbox:

 When the checkbox is selected, auto tracking starts after the direction

of the camera moves to the preset position.

[Close] button

Click this button to close the “Preset per sender” setup menu.

2.7.4.2  Configure settings relating to image quality on alarm action

Click “Image compression rate upon alarm detection setup >>” of “Camera action on alarm” on the [Alarm] tab
of the “Alarm” page. (

®

page 153)

156

Operating Instructions

2 Settings

Summary of Contents for WV-X6511N










































































































































































































































































Reviews:

No comments