Panasonic WV-SPN311 Operating Instructions Manual Download | Manualshive

Page: 191 / 218

background image

3.

Click the radio button respective to the desired option to determine whether or not to initialize the settings
after completing the firmware upgrade.

Default:

Do not reset the settings to the default after the upgrade.

Note

•

Note that the settings cannot be restored after an initialization is operated.

4.

Click the [Execute] button.

→

The confirmation window will be displayed.

IMPORTANT

•

After completing the upgrade, delete temporary internet files. (

•

Upgrade the firmware using a PC in the same subnet as the unit.

•

Follow the instructions from the dealer when upgrading the firmware.

•

When upgrading the application software, use the designated file (extension: img) for the firmware
upgrade.
The name of the firmware to be used for the upgrade should be “model name (Use small letters.
“WV-” is not required.)_xxxxx.img”.
* (“xxxxx” indicates the version of the firmware.)

•

Do not turn off the power of the camera during the upgrade process.

•

Do not perform any operation during upgrading and wait until it completes.

•

The following network settings will not be reset when upgrading the firmware after selecting “Reset the
settings to the default after completing the upgrade. (Except the network settings)”.
Primary server address and secondary server address DNS settings for IPv4, primary DNS server
address and secondary DNS server address settings for IPv6, On/Off for DHCP, IP address, subnet
mask, default gateway, HTTP port, HTTPS port, connection protocol (HTTP/HTTPS), CRT key, server
certificate, UPnP setting, line speed, bandwidth control (bit rate), time & date

•

The viewer software used on each PC should be licensed individually. Refer to your dealer for the
software licensing.

18.3 Check the status [Status]

Click the [Status] tab of the “Maintenance” page. (

®

page 41, page 43)

Operating Instructions

191

18 Maintenance of the camera [Maintenance]

«
...
189
190
191
192
193
...
»

Summary of Contents for WV-SPN311



























































































































































































































Reviews:

No comments

Related manuals for WV-SPN311

Brand: iCarsoft Pages: 2

Brand: Trotec Pages: 20

Brand: GMC Pages: 33

Brand: IFM Pages: 74

SPEED DIAL ULTIMATE

Brand: DAHON Pages: 2

Brand: Pondline Pages: 2

OM-DAQXL-1 Series

Brand: Omega Pages: 85

HS21 BLADECENTER - X5355 FOR SPEC CPU2006

Brand: IBM Pages: 1

HS21 BLADECENTER - L5408 FOR SPEC CPU2006

Brand: IBM Pages: 1

HS21 BLADECENTER - L5240 FOR SPEC CPU2006

Brand: IBM Pages: 1

HS21 BLADECENTER - FOR SPECJBB2005

Brand: IBM Pages: 1

HS21 BLADECENTER - E5345 FOR SPEC CPU2000

Brand: IBM Pages: 1

HS21 BLADECENTER - 5160 FOR SPEC CPU2000

Brand: IBM Pages: 1

HS12 BLADECENTER - X3363 FOR SPEC CPU2006

Brand: IBM Pages: 1

HS12 BLADECENTER - E3113 FOR SPEC CPU2006

Brand: IBM Pages: 1

Coralife BioCube 29 Aurora Array Retrofit

Brand: RapidLED Pages: 19

Brand: Feig Electronic Pages: 36

Brand: Racelogic Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands