Panasonic WORKIO DP-C213, Operating Instructions Manual

Page: 65 / 112

P
rob
lem Solving
65
Code Check Points
J19 Paper Feed Section & ADU Section
(See pages 66, 67, 69, and 70)
J82, J83, ADU Section & Fuser/Exit Section
J88 (See pages 67, and 68)
J30, J31, Paper Feed Section & Fuser/Exit Section
J38, J39, (See pages 66, 68, 69, and 70)
J40,
J42-J45
J41, J50, Fuser/Exit Section & Paper Transport Section
J51, J52, (See pages 68, and 69)
J86
J80, J81, Fuser/Exit Section
J87 (See page 68)
J54-J56 Paper Transport Section
(See page 69)
J60-J66 Optional Finisher Section
(See pages 71-73)
J70-J79 ADF Section
J92-J94 (See pages 74, and 75)
Code Check Points
J00 Sheet Bypass (Remove the misfed paper and
load the paper again)
J01, J11, Paper Tray 1 & Paper Feed Section (Paper
J21 Tray 1-4 & Sheet Bypass) (See page 66)
J02, J12, Paper Tray 2 & Paper Feed Section
J22 (Paper Tray 2) (See page 69)
J03, J13, Paper Tray 3 & Paper Feed Section
J23 (Paper Tray 2-4) (See pages 69, and 70)
J04, J14, Paper Tray 4 & Paper Feed Section
J24 (Paper Tray 3, 4) (See page 70)
J06, J26 Paper Feed Section (Paper Tray 2)
(See page 69)
J07, J08, Paper Feed Section
J09, J27, (Paper Tray 2 & Optional Paper Tray 3 & 4)
J28 (See pages 69, and 70)
J18, J33, Paper Feed Section
J35 (Paper Tray 1-4 & Sheet Bypass)
Verify that the media type selection in the control
panel matches the media loaded on the trays.
Ex: Select "Transparency" when Transparencies
are loaded in the Sheet Bypass
(See pages 66, 69, 70, and 77)
Jam Error Codes (J Codes)
ATTENTION
●
The display indicates the
section of the misfed paper.
Remove the misfed paper,
and check to see if the
misfeed indicator has been
cleared.
If other locations indicate
presence of paper, remove
them and check the display
again.
●
When clearing a misfed
paper that is difficult, or
impossible to see, switch off
the machine and contact the
authorized Panasonic
dealer.
Removing a Misfed Paper (Locations)
●
When a misfed paper occurs, the location and the procedures for
removing misfed paper are displayed frame by frame on the Touch
Panel Display.
Check the location, and remove all misfed papers according to
displayed pictures and this manual. (See pages 66-75)
Ex: ADU Section
Return to 1st step
Misfed Location Indicator
Ex: ADU Section
Finisher
Section
(Option)
ADF (Automatic Document Feeder)
Section
Paper
Transport
Section
(Option)
Paper Tray 1
Paper Tray 2
Paper Tray 3
(Option)
Paper Tray 4
(Option)
Fuser/Exit Section
Paper Feed Section
(Paper Tray 1-4 &
Sheet Bypass)
ADU Section
Sheet Bypass
Paper Feed Section
(Paper Tray 2)
Paper Feed Section
(Paper Tray 3, 4)
(Option)
006Basic_OP(UK)062_065.pmd 16/11/2006, 13:08 65