Panasonic WJ-NX200K Operating Instructions Manual Download

Page: 48 / 204

Configure the settings relating to sub monitors [Sub monitor]

Set up the sub monitor by selecting the camera images to display, the image display duration, etc.

■

Camera title

[Display]

Set whether to display the camera title on the sub
monitor.

On: Displays the camera title
Off: Does not display the camera title

Default:

■

Display settings

Set the display sequence for camera images (image
switching).

[Mode]

Select how to display images from the cameras.

1-screen live sequence: Images from the cameras

will sequentially be switched and displayed on
1-screen.

4-screen live sequence: Images from the cameras

will sequentially be switched and displayed on
4-screen.

9-screen live sequence: Images from the cameras

will sequentially be switched and displayed on
9-screen.

16-screen live sequence: Images from the camer-

as will sequentially be switched and displayed
on 16-screen.

Switch by alarm terminal input: Switches camera

1 to 9 to display images on 1-screen accord-
ing to the signal input triggered by the terminal
alarms from terminal 1 to 9.

24Screen: Images from the cameras will be dis-

played on 24Screen without switching the
screen.

32Screen: Images from the cameras will be dis-

played on 32Screen without switching the
screen.

[Keep aspect ratio]

Select whether to change the aspect ratio of the dis-
played area if the aspect ratio of the image is different
from the displayed area.

Checked: Keep aspect ratio (Does not change the

ratio automatically)

Not checked: Does not keep aspect ratio

(Changes the ratio automatically)

Default:

Not checked

[Duration]

Set the interval (duration) for switching camera
images.

3 s/ 5 s/ 10 s

Default:

5 s

Note:

• The terminal status (N.O. or N.C.) for supplying an

alarm signal to the alarm terminal depends on the
settings for "Terminal input" of "Advanced termi-
nal alarm setup" (

☞

Page 41).

• Some cameras may take time to display images

and the screen may be switched before images
are displayed if the duration is short. In that case,
set a longer time for the switching interval.

[Camera selection]

Select the cameras to be included in the sequence
display.
Mark the checkbox next to the desired camera. The
selected cameras will be displayed in numerical
order.

Note:

• The selected cameras are displayed from the top

in the 4-screen, 9-screen and 16-screen live
sequence, 24Screen or the 32Screen.

• The number of selected camera is within the num-

ber of split screens, it displays without switching
the cameras even if the live sequence is selected.

[Setup via recorder's main monitor]

Summary of Contents for WJ-NX200K













































































































































































































Search results

Summary of Contents for WJ-NX200K

Reviews:

Related manuals for WJ-NX200K

Brands by name

Popular brands

Panasonic WJ-NX200K, Operating Instructions Manual

Search results

Summary of Contents for WJ-NX200K

Reviews:

Related manuals for WJ-NX200K

Brands by name

Popular brands