Panasonic WH-UD03JE5 Service Manual Download Page 75

Page: 75 / 278

12.2.4.2 Wire Stripping and Connecting Requirement

Wire stripping

5mm or

(gap between

wires)

No loose strand

when insert

Indoor/outdoor

connecting

terminal board

PROHIBITED

Conductor

over insert

Conductor not

fully insert

Conductor

fully insert

PROHIBITED

12.2.4.3 Connecting

Requirement

For Tank Unit with WH-UD03JE5, WH-UD05JE5, WH-UD07JE5, WH-UD09JE5



The equipment’s Power Supply 1 complies with IEC/EN 61000-3-2.



The equipment’s Power Supply 1 complies with IEC/EN 61000-3-3 and can be connected to current supply

network.



The equipment’s Power Supply 2 complies with IEC/EN 61000-3-2.



The equipment’s Power Supply 2 complies with IEC/EN 61000-3-11 and shall be connected to suitable supply

network, with the following maximum permissible system impedance Z

max

= 0.352 ohm (

Ω

) at the interface.

Please liaise with supply authority to ensure that the Power Supply 2 is connected only to a supply of that
impedance or less.

12.2.5 Charging and Discharging the

Water



Make sure all the piping installations are properly

done before carry out below steps.

12.2.5.1 Charge the Water



For Domestic Hot Water Tank

1 Set the Domestic Hot Water Tank Discharge

(Drain Tap) to “CLOSE”.

”

“

”

“

Domestic Hot Water Tank Discharge (Drain Tap)

2 Set all Tap / Shower “OPEN”.

3 Start filling water to the Domestic Hot Water

Tank via Tube Connector

After 20~40min, water should flow out from
Tap / Shower. Else, please contact your local
authorized dealer.

4 Check and make sure no water leaking at the

tube connecting points.



For Space Heating / Cooling

1 Turn the plug on the Air Purge Valve outlet

anticlockwise by one complete turn from fully
closed position.

Plug (turn
anticlockwise by
one complete turn)

Air purge valve

2 Set the Pressure Relief Valve lever “DOWN”.

Lever

Turn down

Lever

Turn down

Pressure relief valve

3 Start filling water (with pressure more than

0.1 MPa (1 bar)) to the Space Heating /
Cooling circuit via Tube Connector

. Stop

filling water if the free water flow through
Pressure Relief Valve Drainage .

4 Turn ON the Tank Unit and make sure Water

Pump is running.

5 Check and make sure no water leaking at the

tube connecting points.

Summary of Contents for WH-UD03JE5























































































































































































































































































Search results

Summary of Contents for WH-UD03JE5

Reviews:

Panasonic WH-UD03JE5, Service Manual, Page: 75 / 278

Search results

Summary of Contents for WH-UD03JE5

Reviews: