Home
/
Panasonic
/
WH-UD03JE5
/
Service Manual

Panasonic WH-UD03JE5, Service Manual, Page: 203 / 278

Share

Page: 203 / 278

Panasonic WH-UD03JE5 Service Manual Download Page 203

203

19.5.14 Outdoor High Pressure Abnormality (H64)

Malfunction Decision Conditions:

During operation of cooling and heating, when the outdoor high pressure sensor output signal is 0 Vdc or 5 Vdc.

Malfunction Caused:

1 Faulty

connector

connection.

2 Faulty

sensor.

3 Faulty outdoor unit PCB (main).

Abnormality Judgment:

Continue 4 times in 20 minutes.

Troubleshooting:

For safety reason and to prevent component breakdown,
always switch off the power before remove and connect the component.

Check the CN-HPS connector connection:
- Turn OFF the power.
- Check the connector connection.

Check the continuity of the outdoor unit PCB (main)
high pressure sensor connector CN-HPS:
- Plug out connector from the outdoor unit PCB (main).
- Measure the continuity pin 1 & 3 (GND) and pin 1 &

4 (5 V) of CN-HPS.

Is the CN-HPS connector

connection normal?

Is the measured voltage

0 Vdc or 5 Vdc?

Reconnect the high pressure sensor

connector to the outdoor unit PCB (main).

Turn ON the power and run the system.

Measure the DC voltage pin 1 & 3 (GND)

of CN-HPS.

Is there any continuity?

Yes

Yes

Yes

No

No

No

- Connector poor contact.
- Correct the connection.

- Defect in outdoor unit

PCB (main).

- Replace the outdoor

unit PCB (main).

- Defect in outdoor high

pressure sensor.

- Replace the outdoor
high pressure sensor.

- Detect in outdoor unit

PCB (main).

- Replace the outdoor

unit PCB (main).

Caution

«
...
201
202
203
204
205
...
»

Summary of Contents for WH-UD03JE5























































































































































































































































































Reviews:

No comments