manualshive.com logo in svg

Panasonic WH-UD03JE5, Service Manual, Page: 166 / 278

Share
Download
Panasonic WH-UD03JE5 Service Manual Download Page 166

166 

15.2  Protection Control for Heating Operation 

15.2.1  Outdoor Air Temperature Control 

The maximum current value is regulated when the outdoor air temperature rises above 14°C in order to avoid 
compressor overloading. 

15.2.2 Deice Operation 

When outdoor pipe temperature and outdoor air temperature is low, deice operation start where outdoor fan motor 
stop. 
Normally, deice start if pipe sensor temperature fulfil deice condition. If remote controller set to AUTO force defrost 
setting, unit will start force deice after heat pump operate for 3 hours without deice at below outdoor temperature 5°C 
 

  Deice judging condition 

 

Outdoor Unit Deice Control

Deice starts depends:

1. Outdoor air sensor temp.
2. Outdoor pipe sensor temp.
3. Heating accumulation time.

10

5

0

-5

-10

-15

-20

-25

-30

-30

-20

-10

0

OD

P

ipe

Te

mperat

ure

(°C)

10

20

30

Outdoor Temperature (°C)

When Heating Time > 35 minutes
and Pipe Temperature below this
line for continuous 3 minutes.

 

 
Deice operation time diagram 
 
 

a. Deice mode 1 control: 

 

OD fan

ID pump

Expansion valve

Four way valve

Compressor

Free

Free

ON

OFF

OFF

N

O

N

O

Free

5

7

6

4

9

8

3

2

1

ON

ON

Free

Free

max 9 minutes 30 seconds

deice 1

 

15.2.3  Force Defrost Operation 

Force defrost can be set through remote control with two selection (Manual OR Auto). 
 

  If Manual defrost set, heat pump only run force defrost at heat mode when force defrost request from quick menu 

remote control. 

  If Auto defrost set, heat pump automatically run force defrost operation after 3 hours heating accumulation time 

without defrost when ambient below 5°C. 

 
 
 
 

Summary of Contents for WH-UD03JE5























































































































































































































































































Reviews:

No comments