manualshive.com logo in svg

Panasonic WH-UD03JE5, Service Manual, Page: 164 / 278

Share
Download
Panasonic WH-UD03JE5 Service Manual Download Page 164

164 

15.  Protection Control (WH-UD03JE5  WH-UD05JE5) 

15.1  Protection Control for All Operations 

15.1.1  Time Delay Safety Control 

1  The compressor will not start for three minutes after stop of operation. 

15.1.2  30 Seconds Forced Operation 

1  Once the compressor starts operation, it will not stop its operation for 30 seconds. 
2  However, it can be stopped using control panel at indoor unit. 

15.1.3  Total Running Current Control 

1  When the outdoor running current exceeds X value, the compressor frequency will decrease. 
2  If the outdoor running current does not exceed X value, the compressor frequency will return to normal 

operating frequency. 

3  If the outdoor running current continue to increase till exceed Y value, compressor will stop, and if this occurs 

3 times within 20 minutes, system will stop operation and OFF/ON control panel LED will blink (F16 error 
occurs). 

 

 UD03JE5 

UD05JE5 

Operation Mode 

X (A) 

Y (A) 

X (A) 

Y (A) 

Heating 

11.0 14.0 11.0 14.0 

Cooling 

7.0 14.0 8.3 14.0 

 

A.  DC Peak Current Control 

1  When the current to IPM exceeds set value, compressor will stop. Compressor will restart after three minutes. 
2  If the set value exceeds again for more than 30 seconds after the compressor restarts, operation will restart 

after two minutes.  

3  If the set value exceeds again for within 30 seconds after the compressor restarts, operation will restart after 

one minute. If this condition repeats continuously for seven times, system will stop operation and OFF/ON 
control panel LED will blink (F23 error occurs). 

15.1.4 Compressor Overheating Prevention Control 

  The compressor operating frequency is regulated in accordance to compressor tank temperature as shown in 

below figures. When the compressor tank temperature exceeds 112°C, compressor will stop, and if this occurs  
4 times within 30 minutes, system will stop operation and OFF/ON control panel LED will blink (F20 error occurs). 

 

Compressor = OFF

Compressor

Frequency Reduced

Compressor

Frequency Maintain

Free

Compressor tank temperature

112°C

110°C

108°C

97°C

97°C

97°C

 

 
 
 
 
 
 
 
 

Summary of Contents for WH-UD03JE5























































































































































































































































































Reviews:

No comments