Home
/
Panasonic
/
WH-UD03JE5
/
Service Manual

Panasonic WH-UD03JE5, Service Manual, Page: 135 / 278

Share

Page: 135 / 278

Panasonic WH-UD03JE5 Service Manual Download Page 135

135



Case 2: Tank Heater OFF OR External Heater is select

o

When heat pump OFF due to water thermos & Tank temperature > Tank water set temperature for
continuously 20 seconds.

OR

o

Tank temperature > Tank set tempe 1°C for continuously 20 seconds.

Tank Thermo ON

Case 1: Tank Heater ON (Internal Tank Heater)

o

Tank temperature < Tank set tempe R/C (Tank re-heat temperature)

Case 2: Tank Heater OFF (Internal Tank Heater)

o

Tank temperature < Tank water set tempe R/C (Tank re-heat temperature)

* When tank thermo ON, water pump will ON for 3 minutes then only heat pump turn ON.

* Tank water set temperature = tank set temperature or 52°C whichever lower.



2 ways valve close



Heat pump Thermostat Characteristic

o

Heat pump Water Outlet set temperature is set to below table:

Outdoor ambient temperature

Heat pump target water outlet temperature

< -10°C

56°C

> -10°C

59°C

Characteristic of heat pump thermos ON/OFF under tank mode condition:

Water Outlet Thermo Condition



Heat pump thermos OFF temperature:

1 Heat pump thermo OFF temperature = Target Water outlet tempe (1°C)
2 Water outlet temperature > heat pump thermo OFF temperature for continuously 3 minutes, heat pump OFF

but water pump continue ON.



Heat pump thermo ON temperature

1 Heat pump thermo ON temperature = water inlet during thermo OFF time + [-3°C]
2 When water outlet temperature < heat pump thermo ON temperature, heat pump ON.

Water inlet thermo protection condition



Heat pump thermo OFF temperature:

1 Water inlet temperature > [60°C/55°C] for continuously 30 seconds, heat pump OFF, water pump continue

ON.



Heat pump thermo ON temperature:

1 Heat pump thermos ON temp = water inlet temperature < [60°C/55°C].

Outdoor ambient temperature

Water inlet temperature

< -10°C

55°C

>-10°C 60°C

Thermo ON/OFF for Heat Pump in Tank Operation:

When tank temperature achieve heat pump OFF condition, refer below condition:
Conditon 1 : Tank Heater ON (Internal Tank Heater)



Heat pump will turn OFF, water pump continue ON and room heater will continue ON if tank temperature below

tank heater thermo ON condition. 3 ways valve will only switch to room side after tank temperature reach tank
heater thermo OFF condition.

«
...
133
134
135
136
137
...
»

Summary of Contents for WH-UD03JE5























































































































































































































































































Reviews:

No comments