manualshive.com logo in svg

Panasonic WH-UD03JE5, Service Manual, Page: 103 / 278

Share
Download
Panasonic WH-UD03JE5 Service Manual Download Page 103

103 

operate heat pump only

Alternative mode

Outdoor temp.

operate heat pump only

Parallel mode

Outdoor temp.

operate heat pump only

For heating

Outdoor temp.

Advanced Parallel mode

AND

operate heat pump only

For DHW tank

Outdoor temp.

AND

Heat pump
thermo ON

Tank

temp.

Heat

pump

10. External SW

System setup

Base pan heater

External SW

Select

11. Solar connection

System setup

Alternative outdoor sensor
Bivalent connection
External SW

Select

operate boiler only

-10°C (setting from remote controller)

operate boiler and heat
pump simultaneously

-10°C (setting from remote controller)

Although heat pump operates

but water temperature does

not reach this temperature for

more than 30 mins (setting

from remote controller)

Circulation water temp.

Boiler temp. ON

= Setting -8°C

(setting from

remote controller)

Boiler temp. OFF

= Setting -2°C

(setting from

remote controller)

Setting temp

In Advanced Parallel mode, setting for both heating and tank can
be made simultaneously. During operation of “Heating/Tank” mode,
when each time the mode is switched, the boiler output will be
reset to OFF. Please have good understanding on the boiler control
characteristic in order to select the optimal setting for the system.

operate boiler and heat
pump simultaneously

-10°C (setting from remote controller)

operate boiler and heat
pump simultaneously

-10°C (setting from remote controller)

Tank temp.

Lowering

If actual tank temp. does

not achieve the setting

temp. within 30min

(setting from remote

controller), the boiler

turn ON

When tank

temp. is

achieved, both

operations

stop

Boiling initial

temp.

Boiler

30 min (setting from

remote control)

Tank setting

temp.

time

Initial setting: No

Able to turn ON/OFF the operation by external switch.

12:00am,Mon

12:00am,Mon

Alternative outdoor sensor
Bivalent connection

Con

fi

rm

Con

fi

rm

Initial setting: No

Set when solar water heater is installed.

Setting include items below.

1
2

3

4
5

Set either buffer tank or DHW tank for connection with solar water heater.
Set temperature difference between solar panel thermistor and buffer tank or
DHW tank thermistor to operate the solar pump.
Set temperature difference between solar panel thermistor and buffer tank or
DHW tank thermistor to stop the solar pump.

Anti-freezing operation start temperature (please change setting based on usage of glycol.)
Solar pump stop operation when it exceeds high limit temperature (when tank temperature exceed designated temperature (70~90°C))

Solar connection

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for WH-UD03JE5























































































































































































































































































Reviews:

No comments