48
VL-SWD272BX/SWD272CX/SWD272CX1/SWD272AZ/VL-WD613CX/VL-WD613CX1
9.3.7.
Before Using
• When power fails, this unit cannot be used.
• For the recorded image:
The recorded image may be lost when:
-Mishandled
-Electric shock or radio wave interference occurs.
-The power is turned off during use.
(We might not be held responsible for the damage.)
9.3.8.
Location/avoiding noise (Main monitor station/wireless monitor station)
The main monitor, wireless monitor, and other compatible Panasonic units use radio waves to communicate with each other.
(The product operates in the frequency range of 1.88 GHz to 1.90 GHz, and the RF transmission power is 250 mW (max.).)
• For maximum coverage (approx. 100 m) and noise-free communications, install your main monitor:
- at a convenient, high, and central location with no obstructions between the wireless monitor and main monitor in an indoor
environment.
- away from electronic appliances such as TVs, radios, personal computers, wireless devices, or digital cordless phones.
- facing away from radio frequency transmitters, such as external antennas of mobile phone stations.
(Avoid installing the main monitor near a window.)
• Coverage and voice quality depends on the local environmental conditions.
• Do not place the charger near TVs, speakers, or other devices that emit electromagnetic waves.
Failure to do so may prevent the charger from charging the product.
9.4.
Error Messages
n
Main monitor station
n
Wireless monitor station
Problem
Cause & Solution
“Cannot register”
• Registration failed because it was not completed within the specified time.
→
Check that the devices to be registered are correctly connected and receiving
power, and then try again.
Problem
Cause & Solution
“Cannot connect to main
monitor station”
• The wireless monitor is too far from the main monitor, or there is an object such as
a concrete wall obstructing the signal.
→
Move the wireless monitor closer to the main monitor or to an area that does not
have any obstructions. If the camera
cannot be moved to another area, installing a repeater (additional accessory)
may improve the signal.
“Registration failed”
• Registration to the main monitor has not been completed. Bring the wireless moni-
tor closer to the main monitor and try registering again.
Summary of Contents for VL-MWD272BX
