Panasonic Vericam 35, Operating Manual

Page: 109 / 119

– 109 –
Chapter 11 Maintenance and Inspection — Warning system
Display Description Behavior and cause
[PROXY REC WARNING] A proxy data recording error occurred.
f
The current operation will continue.
f
Turn off the camera and turn on it again to check the
recording and playback. If the error continues to occur,
please consult your dealer.
[REC IMPOSSIBLE] (slot number)
An SDHC/SDXC memory card is inserted into the
microP2 memory card slot.
Recording to the SDHC/SDXC memory card is disabled.
f
The current operation will continue.
f
Record to microP2 or P2 memory cards.
[REC WARNING]
[FRAME SIGNAL]
Displayed when a video or audio error occurs during
recording.
f
Warning lamp flashes four times per second during
continuous recording.
f
The current operation will continue. When input
signals are disrupted, recording continues while
disrupted images are recorded. Check the signal to be
input to the camera.
f
Turn off the power and on before using it again.
[REC WARNING]
[OVER MAX# CLIPS]
Displayed when attempting to record in excess of the
maximum total number of clips allowed for one P2 card.
f
Warning lamp flashes four times per second during
continuous recording.
f
The operation will stop.
f
Replace the P2 card or delete unnecessary clips.
[REC WARNING]
[PULL DOWN]
(Occurs during recording)
The video pull-down sequence and time code values
are not synchronized.
f
Warning lamp flashes four times per second during
continuous recording.
f
The current operation will continue.
f
Check the signal.
[REC WARNING]
[PULL DOWN ERROR]
(Occurs at times other than during recording)
The video pull-down sequence and time code values
are not synchronized.
f
The current operation will continue.
f
Check the signal.
[REC WARNING]
[REC DATA]
Displayed when an error occurs in recorded data during
recording.
f
Warning lamp flashes four times per second during
continuous recording.
f
The operation will continue or stop.
f
Turn off the power and on before using it again.
[RUN DOWN CARD] (slot number)
The maximum number of overwrites has been
exceeded.
f
The current operation will continue.
f
Replacement of the P2 card is recommended.
[SD CARD] (slot number)
An SDHC/SDXC memory card is inserted into the
microP2 memory card slot.
f
The current operation will continue.
f
Use of microP2 or P2 memory card is recommended.
[TEMPORARY PAUSE]
[IRREGULAR SIG]
Recording is temporary suspended due to correct
recording not possible because of the disruption of input
signal from the <GENLOCK IN> terminal. The clip will
be divided.
f
Warning lamp flashes four times per second during
continuous recording.
f
The operation will pause.
f
Recording will resume when the signal returns to
normal.
During thumbnail and menu operation
Display Description Behavior and cause
[AUTHENTICATION ERROR!] Manual authentication failed. Enter the correct password.
[CANNOT ACCESS!]
Data cannot be accessed due to a content defect or
some other reason.
Ensure the health of the media and the clips.
[CANNOT CHANGE!]
For a clip with the mark, where a thumbnail cannot
be generated, the thumbnail cannot be modified in the
text memo position.
Correct the settings and content to enable display of the
thumbnail.
[CANNOT DELETE!] The content versions do not match. Cannot delete. Match the device and contents version.
[CANNOT FORMAT!]
A P2 card problem or some other reason prevents
formatting.
Check the P2 card.
[CANNOT RE-CONNECT!]
Clips cannot be remerged because either clips not
recorded across multiple P2 cards are selected or other
reasons.
Check the selected content.
[CANNOT REPAIR IN SELECTION!] Some of the selected clips cannot be repaired. Check the selected content.
[CANNOT REPAIR!] Content that cannot be repaired is selected. Check the selected content.
[CANNOT SAVE! FILE NAME IN USE]
A settings file of the same name exists on the SD
memory card.
Use another name to save the file.
[CARD FULL!] The P2 card or SD memory card is full. Insert a card with free space available.
[COPY IMPOSSIBLE. TOO LARGE CLIP
CONTAINED! (CLIP NAME: XXXXXX)]
Files exceeding 4 GB cannot be copied to P2 memory
card or microP2 memory card with 32 GB or smaller
capacity.
Copy to a microP2 memory card with 32 GB or larger
capacity.
[INVALID VALUE!] The data value you entered is invalid. Enter data within the normal range.
[LACK OF CAPACITY!] There is not enough recording capacity left on the card. Insert a card with sufficient recording capacity.
[MISSING CLIP!]
Shot marks cannot be attached to the clips unless all
clips recorded over multiple P2 cards are present.
Insert all P2 cards over which recording extended.
[NO CARD!] No P2 or SD memory card is inserted. Insert the relevant media.
[NO COPY TO SAME CARD!]
A clip cannot be copied to the card storing the original
clip.
Copy the selected clip to a card that does not contain
the original clip.
[NO FILE!] The specified file does not exist. Check the file.
[NO INPUT!] No data is entered. Enter data and then set.