Panasonic VB-44210G User Manual Download

Page: 98 / 394

Chapter 3. System Features

Section 700 - Operation

Page 3-52

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Figure 2-2. SMDR Format for CPC-AII and CPC-B Version 3.1 or higher

0 1 2 3 4 5 6 7

012345678901234567890123456789012345678901234567890123456789012345678901234567

1 2 3 4 5 6 7 8 9

T MM/DD HH:MM:SS HH:MM.SS NNN DDDDDDDDDDDDDDDDDDDDDDDDDDDD AAAAAAAAAA VVVVV NN

1=Call type

S=Inbound DISA

s=Outbound DISA

I=Incoming

O=Outgoing

T=Transfer (See Note 1.)

N=DNIS

D=DID

2=Date

MM=month

DD=day

3=Call start time

HH=hours

MM=minutes

SS=seconds

4=Call duration

HH=hours

MM=minutes

SS=seconds

5=Extension number

10-69, 100-699=extensions

CO number=DISA

6=Dialed digits or Caller ID

DD=digits 0-9 or symbols * or

(See Note 2.)

7=Account code

A=0-9999999999

8=Verified account code or walking

COS code

V0000-V9999=verified account codes

W0000-W9999=walking COS codes

9=Trunk Number

NN=number (01-64)

Notes:

1. Transferred calls include direct and group call pickups and conference calls.

If a station call is transferred to an outside number, an SMDR record is

also created for the station that is transferred.

2. The * symbol appears as a greater-than sign (>) on the SMDR printout; the # symbol

appears as a less-than sign (<). Centrex and PBX codes, as well as LCR access codes, do

not appear as dialed digits. If the Caller ID Feature is installed and enabled,

“Private” appears with calls that have restricted Caller ID display and “Out of Area”

with long distance calls that do not provide Caller ID information.

Summary of Contents for VB-44210G











































































































































































































































































































































































































Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands

Panasonic VB-44210G, User Manual

Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands