Panasonic VB-44210G User Manual Download | Manualshive

Page: 85 / 394

background image

Section 700 - Operation

Chapter 3. System Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page 3-39

Off-Premises Extension

(All Versions)

Description

SLTs that are located in remote locations can be connected to the DBS
through the Off-Premises Extension (OPX) Adaptor.

Off-premise phones can be connected through a direct line to the DBS or
through the central office, depending on how far they are from the main
cabinet. For specifications, see

Installation (Section 300).

Operation

Feature operation for OPX extensions is the same as for local SLTs connected
to the DBS.

Related Programming

• FF3 (Extension): Terminal Type

Hardware Requirements

• One OPX Adaptor (VB-43702) is required for each OPX extension.

• When OPX extensions are connected through the central office, an

external ringer supply may be required. If required, the ringing supply is
connected to the OPX Adaptor.

Considerations

• Up to 8 OPX extensions can be connected to a system.

• The DBS side of the OPX Adaptor is connected to a

digital

extension port.

Paging

(All Versions)

Description

Internal paging is accomplished through the speakers of your system’s key
phones. The Paging feature allows you to contact someone temporarily away

«
...
83
84
85
86
87
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Samsung Pages: 60

Brand: Samsung Pages: 2

Brand: Samsung Pages: 24

Brand: Samsung Pages: 22

Brand: Samsung Pages: 23

Brand: Yeastar Technology Pages: 12

Brand: Samsung Pages: 67

Brand: Olympia Pages: 28

Brand: Subpac Pages: 15

Brand: Dickson Pages: 28

Brand: Daewoo Pages: 21

Brand: TransTel Communications Pages: 48

Brand: Uniden Pages: 64

Brand: JabloCom Pages: 2

Brand: AmpliVox Pages: 8

FortiFone FON-870i

Brand: Fortinet Pages: 21

Brand: Spitfire Pages: 2

Brand: MOBICEL Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands