Panasonic VB-44210G User Manual Download | Manualshive

Page: 70 / 394

background image

Chapter 3. System Features

Section 700 - Operation

Page 3-24

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Direct Trunk Access

(All Versions)

Description

Extensions can access a specific trunk for outgoing calls. Extensions can also
use Direct Trunk Access to test trunks or to access data trunks.

Operation

1. Press

the

ON/OFF

key:

• The phone issues intercom dial tone.

• The

ON/OFF

LED lights.

2. Dial “88,” then enter the desired line number (01-64).

• The phone issues outside dial tone.

• “CO TALK #XX” (where “XX” is the line number) appears on the

display.

3. Dial the telephone number.

The number appears on the display.

4. Complete the call and replace the handset.

Distinctive Ringing

(CPC-AII and CPC-B Version 3.1 or higher)

Description

Distinctive trunk call ringing patterns can be set up for each extension using
the Distinctive Ringing feature. Distinctive Ringing allows users to determine
which extension is ringing when several telephones are in the same area. If no
distinctive ringing pattern is set, the extension rings based on the incoming
ring pattern assigned to the trunk.

Related Programming

• FF3 (Extension): Extension Ring Pattern

«
...
68
69
70
71
72
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Samsung Pages: 6

Brand: 3Com Pages: 3

Brand: 3Com Pages: 2

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

KX-TG7622, KX-TG7623, KX-TG762

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 6

Brand: AT&T Pages: 7

XDECT 8155 Series

Brand: Uniden Pages: 68

Brand: Swisscom Pages: 14

Aegis-09 Series

Brand: Scitec Pages: 4

Brand: Clas Ohlson Pages: 2

efector190 DTE810

Brand: IFM Electronic Pages: 38

Brand: Teufel Pages: 20

Brand: invotel Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands