Panasonic VB-44210G User Manual Download Page 68 | Manualshive

Page: 68 / 394

background image

Chapter 3. System Features

Section 700 - Operation

Page 3-22

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Direct Inward System Access (DISA)

(All Versions)

Description

Direct Inward System Access (DISA) gives off-site users dial-in access to the
DBS. Users access DISA by dialing a 7-digit number assigned to a DISA
trunk.

For security reasons, one incoming DISA code and two outgoing DISA codes
can be assigned. If an incoming code is assigned, it must be entered as soon as
the DISA trunk answers. An outgoing code must be entered before the user
dials an outgoing call.

Operation

To make a DISA call to an extension:

1. Dial the DISA trunk number.

2. Once you hear DISA dial tone from the DBS, enter the 4-digit DISA code

(if an incoming DISA code is assigned). If the incoming DISA code is not
programmed, you can proceed to the next step.

3. Dial the extension number.

To make a DISA call to an outside number:

1. Dial the DISA trunk number.

2. Once you hear DISA dial tone from the DBS, enter the 4-digit DISA code

(if an incoming DISA code is assigned). If the incoming DISA code is not
programmed, you can proceed to the next step.

3. Dial #7 plus the 4-digit Outgoing DISA Code.

Two outgoing DISA codes are assigned. Either may be used after the #7.

4. Dial the trunk group number you want to use (81-86 or 9).

5. Dial the desired telephone number.

Related Programming

• FF1 (System): Direct Inward System Access (DISA) ID Code

«
...
66
67
68
69
70
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Waters Pages: 116

Brand: AT&T Pages: 26

Soundgear Series

Brand: JBL Pages: 73

Brand: AKG Pages: 49

Brand: GE Pages: 22

Maestro 4625 Owner's

Brand: Aastra Pages: 38

Brand: Excelltel Pages: 22

Brand: Plantronics Pages: 2

Brand: B&R Industries Pages: 16

Brand: Technics Pages: 14

Brand: RCA Pages: 11

Brand: BRONDI Pages: 16

Brand: Hitachi Pages: 35

Brand: Hitachi Pages: 33

Brand: Hitachi Pages: 40

Brand: Hitachi Pages: 28

Brand: Hitachi Pages: 26

Brand: Hitachi Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands