manualshive.com logo in svg

Panasonic VB-44210G, User Manual

The Panasonic VB-44210G User Manual is essential for maximizing the potential of your phone system. This comprehensive manual provides step-by-step instructions and troubleshooting tips, ensuring a seamless user experience. Download it for free from manualshive.com and unleash the full capabilities of your Panasonic VB-44210G.

Share
Download
background image

Section 700 - Operation

Chapter 2. Attendant Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

  2-21

the personal VM key is not assigned to the lowest-numbered key, it will not 
flash to indicate VM messages.

Station Lockout Code Assignment

 (All Versions)

Description

The Station Lockout feature allows users to dial a Station Lockout code to 
restrict their phone from being used for outside calls.

Station Lockout codes can be assigned through the attendant phone.

Operation

To program a Station Lockout code:

1. Press 

the 

ON/OFF

 key.

• The phone issues intercom dial tone.

• The 

ON/OFF

 LED lights.

2. Press 

the 

CONF

 key.

3. Dial 

“#8.”

4.  Dial the extension number.

5.  Enter the desired key code (four digits).

6. Press 

the 

HOLD

 key.

“STORE XXXX” (where “XXXX” is the key code) appears on the 
display.

7. Press 

the 

ON/OFF

 key.

The 

ON/OFF

 LED goes off.

Considerations

• A locked extension can be used for Intercom Calls.

• Station Lockout key codes can also be set through system programming.

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Daewoo DTC-700 User Manual preview
DTC-700
Brand: Daewoo Pages: 32
Badeloft AT-05 Installation Instructions Manual preview
AT-05
Brand: Badeloft Pages: 12
Harman Kardon MaestroKitchen 100 User Manual preview
MaestroKitchen 100
Brand: Harman Kardon Pages: 36
ascon X30A Operating Instructions Manual preview
X30A
Brand: ascon Pages: 8
Battery Watering Technologies PW-180 Installation And Operation Instructions preview
PW-180
Brand: Battery Watering Technologies Pages: 2
Vertical CONVERSip Edge 300 User Manual preview
CONVERSip Edge 300
Brand: Vertical Pages: 48
Uniden XDECT SSE47 Series Owner'S Manual preview
XDECT SSE47 Series
Brand: Uniden Pages: 44
Gigaset A540h Manual preview
A540h
Brand: Gigaset Pages: 27
Namtai Electronic SingStar 7013539 Instruction Manual preview
SingStar 7013539
Brand: Namtai Electronic Pages: 2
Velux CLI U12 SD0F1110 NG B/U Installation Operation & Maintenance preview
CLI U12 SD0F1110 NG B/U
Brand: Velux Pages: 56
Apollo Entertainment KiwiSat Installation And Use Manual preview
KiwiSat
Brand: Apollo Entertainment Pages: 24
Watts AERCO AquaSolve AM8408-COM Operation & Maintenance Manual preview
AERCO AquaSolve AM8408-COM
Brand: Watts Pages: 8
Valcom V-9936A Datasheet preview
V-9936A
Brand: Valcom Pages: 1
RINGSPANN IR Series Installation And Operating Instruction preview
IR Series
Brand: RINGSPANN Pages: 6
Geemarc Amplidect350 User Manual preview
Amplidect350
Brand: Geemarc Pages: 236
SoundPeats QY7 User Manual preview
QY7
Brand: SoundPeats Pages: 14
InfinitePlay ipdoor Flush Quick Start Manual preview
ipdoor Flush
Brand: InfinitePlay Pages: 25
LG LG-RD2710 User Manual preview
LG-RD2710
Brand: LG Pages: 75

Brands by name

Popular brands

Load more brands