Panasonic VB-44210G User Manual Download Page 367 | Manualshive

Page: 367 / 394

background image

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page I-3

This only occurred on the first ring. After the first ring, the ringing pattern
returned to normal. The ringing pattern for incoming ISDN calls now rings as
expected.

Calling Party Could be Heard Between Rings

- In the previous version,

when an ISDN call was transferred, the station receiving the call could hear
the calling party between rings. This problem has been corrected in this
version.

Dial Tone Received After Placing Call

- Previously, when placing an

outgoing call after dialing the number, the caller would receive another dial
tone. This problem has been corrected in this version.

ISDN Calls Disconnected

- Previously if an ISDN-to-ISDN call was

attempted, and the called party was busy, instead of receiving CO Busy the
call was dropped. This problem has been corrected in this version.

16-Port Voice Mail Support via API

Description

This feature allows up to sixteen (16) voice mail ports via API integration.

Programming

Programming

See

Section 400 - Programming (Appendix K)

for more detailed

programming information.

Operation

N/A

Notes

• All additional voicemail programming must be completed on the entire 16

ports for the voice mail to function properly.

• Voice mail ports should be on consecutive AEC or DEC cards.

«
...
365
366
367
368
369
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: NEC Pages: 334

Brand: NEC Pages: 12

Brand: DAC Limited Pages: 12

Brand: Viking Pages: 2

STARPLUS Triad-S 1

Brand: Vodavi Pages: 19

Brand: Nady Systems Pages: 12

Brand: Maxview Pages: 24

Brand: AT&T Pages: 4

Brand: Daewoo Pages: 48

Brand: Grundig Pages: 16

Brand: Topcom Pages: 28

Brand: Daewoo Pages: 21

Brand: DAEWOO ELECTRONICS Pages: 7

Brand: Shiro Pages: 23

Brand: Pure Water Pages: 22

Brand: ISOUND Pages: 28

Brand: Nebulink Pages: 12

Brand: DFI Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands