Panasonic VB-44210G User Manual Download Page 347 | Manualshive

Page: 347 / 394

background image

Section 700-Operation

Appendix B. CPC-AII/B 8.0 Feature Update

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page B-21

TAPI Support

CPC-AII/B offers full support for the Panasonic Telephony Applications Processing Interface
(TAPI). TAPI is a Windows™ application which allows a PC to be connected to a telephone
extension and used to control incoming and outgoing calls through that extension. Typical
PC applications that might be used with TAPI include Contact Managers and Personal
Organizers.

The Panasonic TAPI product (VB-43720) provides the necessary interface between a DBS
and a PC-based TAPI application. This product consists of a TAPI Adapter and the Panasonic
TAPI Service Provider (SP) software which resides on the PC. The TAPI Adapter provides
the physical connection between a PC, a DBS extension, and the DBS itself. Its purpose is to
intercept telephone and call control signaling messages from the DBS and telephone
extension and then forward a copy of those messages to the Service Provider software on the
PC. After interpreting the messages, the Service Provider software passes them on to the
TAPI application.

No special programming of the DBS is required for TAPI. For detailed information, see the

TAPI Installation Guide, Part Number 575X00201, Section 570

.

Key Telephone Installation Notes

Desi Strip Cover

The 44-Series Key Telephones are shipped with a thin green protective film over the Desi
strip cover. Be sure to remove this film from both sides of the Desi cover before placing the
phone in service.

Key Telephone Wall Mounting Instructions

The following procedures apply to 44-Series Key Telephones only. Please be sure to follow
these procedures exactly. Removing the desk stand incorrectly can result in damage to the
telephone and/or desk stand.

1. Place the telephone face down on a flat surface.

2. Grasp the top of the desk stand (at the

>ABS<

label) and pull up the end to 90° vertical

(refer to Step 2 in Figure D-19). The stand will click as it releases from the plastic securing
latches.

3. Lift the desk stand as shown in Step 3 of Figure D-19.

«
...
345
346
347
348
349
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: GE Pages: 28

Brand: Talkswitch Pages: 26

Brand: Wayne Pages: 16

Aqua-Pure AP510

Brand: 3M Pages: 16

DECT1560 Series

Brand: Uniden Pages: 64

Passport Conference 2 Series

Brand: Fender Pages: 20

Brand: Tokai Pages: 20

Brand: Pyle Pages: 8

Brand: Jensen Audio Pages: 20

Brand: Jaycar Pages: 8

Brand: QFX Pages: 7

Brand: Endon Pages: 2

Brand: Sagem Pages: 170

Brand: Korg Pages: 6

Brand: Valcom Pages: 1

Brand: Crystal Quest Pages: 8

ClearSound MyDECT 100

Brand: Geemarc Pages: 71

Brand: Shure Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands