Panasonic VB-44210G User Manual Download Page 33 | Manualshive

Page: 33 / 394

background image

Section 700 - Operation

Chapter 2. Attendant Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

2-13

Operation

To disable the intercom dial tone:

1. Press

the

ON/OFF

key.

• The phone issues intercom dial tone.

• The

ON/OFF

LED lights.

2. Press

“#50.”

3. Press

the

ON/OFF

key.

The

ON/OFF

LED goes off.

To reactivate dial tone:

Repeat the preceding steps.

DSS/72

(All Versions)

Description

The DSS/72 is a 72-key console that can be attached to the attendant phone.

The 72 keys of the DSS can be programmed as Direct Station Select (DSS)
keys for internal lines. In addition to providing direct station selection, the
DSS keys also provide busy lamp fields to assist the attendant in monitoring
the status of extensions.

The attendant can perform a simplified call transfer by pressing a DSS key
while connected to an outside line. The outside line is placed on hold and the
extension is dialed automatically.

When the attendant is placed in the programming mode, the DSS can be used
for inputting text names. Figure 1-1 shows which keys are pressed for text
input.

«
...
31
32
33
34
35
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Aastra Pages: 69

Brand: Gigaset Pages: 2

Brand: KAM Pages: 4

Brand: Medion Pages: 308

Brand: Audiovox Pages: 40

HA9888(69)TSD-S

Brand: Bittel Pages: 7

Brand: BIO-MICROBICS Pages: 12

Quad-MC EV9628-28

Brand: Everpure Pages: 2

Brand: Hama Pages: 14

Brand: BRONDI Pages: 16

Audio 2000's AMW6304U

Brand: H & F Technologies Pages: 6

Brand: Aristel Pages: 67

Brand: Sharp Pages: 72

Brand: ausdom Pages: 51

Brand: SOYO Pages: 9

Brand: Technicolor Pages: 126

Brand: Siemens Pages: 2

Brand: Siemens Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands