Panasonic VB-44210G User Manual Download | Manualshive

Page: 268 / 394

background image

Chapter 6. SLT Features

Section 700 - Operation

6-12

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

3. Enter the Park Number assigned to the call.

“PARK PICK XX” (where “XX” is the park number) appears, and then
“CO TALK #XX” (where “XX” is the trunk number of the call) appears.

Related Programming

• FF1 (System): Park Recall Timer

Considerations

• The parked call recalls if it is not retrieved before the Recall Timer expires.

If this happens, the user that parked the call can retrieve it by picking up
the handset. If no one retrieves the call after the Park Recall Timer expires,
the call reverts to the attendant.

• You cannot park more than one outside line at a time.

• The Park Recall Timer is similar to the Recall Timer, except that when the

Park Recall Timer is set for “0” calls are automatically recalled in three
minutes.

Call Pickup

(All Versions)

SLTs can use both direct and group call pickup.

Direct Call Pickup

Description

A call to an extension can be answered from any other extension with the
Direct Call Pickup feature.

Operation

1. Lift the handset.

2. Dial

“79.”

3. Enter the number of the ringing extension.

«
...
266
267
268
269
270
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 64

Brand: Panasonic Pages: 87

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 88

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 214

Brand: Panasonic Pages: 126

Brand: Uniden Pages: 49

TCX905 - Cordless Extension Handset

Brand: Uniden Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands