Panasonic VB-44210G User Manual Download | Manualshive

Page: 266 / 394

background image

Chapter 6. SLT Features

Section 700 - Operation

6-10

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Call Hold

(All Versions)

Description

Call Hold provides either exclusive or system hold, depending on system
programming. With Exclusive Hold, only the extension that held the call can
retrieve it. With System Hold, another extension can retrieve the call.

Operation

To place a call on Hold:

Flash the switchhook.

To release the call:

Flash the switchhook again.

Related Programming

• FF1 (System): Recall Timer for Extension-Held CO Calls

• FF1 (System): Recall Timer for Extension-Held Intercom Calls

• FF1 (System): SLT Onhook Flash Timer

• FF3 (Extensions): Single Line Telephone Hookflash (Broker’s Hold/

Conference)

• FF1 (System): Single Line Telephone Flash Control

Considerations

• A held call recalls if it is not retrieved before the Hold Recall Timer

expires.

• If there is no response to the Hold Recall, the call transfers to the Attendant

Phone; however, no tone sounds at an Attendant Phone if Night Mode is
activated.

• If you flash the switchhook during a conference call, the flash is ignored.

• If your system is set to onhook transfer, and you have placed an outside

call on hold and then made an intercom call, make sure the other extension

«
...
264
265
266
267
268
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 252

KX-TH112 - Cordless Phone - Operation

Brand: Panasonic Pages: 10

Brand: Aastra Pages: 2

Brand: Zeck Audio Pages: 16

digital slim -1400

Brand: Fisher Pages: 20

Hydro-Guard HG-3

Brand: Mueller Pages: 7

Brand: Uniden Pages: 60

Brand: Daewoo Pages: 21

Brand: eMoMo Pages: 2

Brand: W Audio Pages: 8

Brand: Ole Pages: 35

Brand: info-hold Pages: 2

Brand: SAL Pages: 20

Brand: VTech Pages: 56

DECT 2005 Series

Brand: Uniden Pages: 24

Brand: Pure Water Pages: 22

Brand: PalmMicro Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands