Panasonic VB-44210G User Manual Download | Manualshive

Page: 255 / 394

background image

Section 700 - Operation

Chapter 5. DSLT Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

5-37

• Speed Dialing cannot be checked while Station Lockout is enabled.

• If the Speed Dial is used to forward to an outside number and Least Cost

Routing is enabled, the Speed Dial cannot use Trunk Group “9.”

System Speed Dial

Description

Frequently called numbers can be stored using the System Speed Dial feature.
Up to 90 System Speed Dial numbers can be programmed at the Attendant
Phone and used by any extension. With CPC-AII/CPC-B Version 7.0 and
higher, up to 200 System Speed Dial numbers can be programmed at the
Attendant Phone and used by any extension.

Operation

To dial a system speed dial number:

1. Pick up the handset.

2. If necessary, access an outside line.

3. Press

AUTO

.

4. Dial the system speed dial code (00-89 or 000-199).

Related Programming

• FF1 (System): Override Toll Restriction with SSD Numbers

• FF10 (Speed Dialing): System Speed Dialing

Station Lockout

(All Versions)

Description

Use the Station Lockout feature to dial a Station Lockout code that prevents
other users from using your phone.

«
...
253
254
255
256
257
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: abc Pages: 8

Brand: Icom Pages: 75

Brand: Pacific Sun Pages: 12

DVX-2000MS-10P - VoiceCenter IP Phone Sys...

Brand: D-Link Pages: 20

Brand: Yealink Pages: 8

Brand: Yealink Pages: 2

Brand: JPS Pages: 116

Brand: ZETRON Pages: 60

MM2040 TOUCHBOX

Brand: Manta Pages: 16

Brand: Globalmediapro Pages: 11

Brand: Meeteasy Pages: 2

151 Musiccenter

Brand: Burmester Pages: 20

Brand: Eaton Pages: 142

LINKBRIDGE LBO-DP12-R-2F

Brand: Broadata Communications Pages: 14

Brand: CHARITY MOBILE Pages: 14

Brand: DMGT Pages: 3

Brand: Sharp Pages: 18

Brand: Honeywell Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands