Panasonic VB-44210G User Manual Download Page 25 | Manualshive

Page: 25 / 394

background image

Section 700 - Operation

Chapter 2. Attendant Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

2-5

Operation

To override a busy extension:

Press “4.”

“CONF XXX YYY” (where “XXX” and “YYY” are the extension numbers)
appears on the display.

Related Programming

• FF1 (System): Attendant Override

• FF1 (System): Alert Tone for Busy Override & OHVA

Considerations

• Replace the handset to exit the three-party conference call.

• The alert tone can be turned on or off through system programming.

Attendant Call Park

(All Versions)

Description

Using the Attendant Call Park feature, the Attendant may park an outside call
until the called party can be found. The attendant can then use the Paging
feature to inform the called party of the call’s Park Number. The parked call
can then be retrieved from any extension by dialing the Park Number.

The attendant phone is equipped with ten outside line Park Numbers (00-09).
Programming a Call Park key into an FF key on a telephone or a DSS console
makes one-touch Call Park possible.

Operation

To park an outside call:

1. Press

the

HOLD

key.

«
...
23
24
25
26
27
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Aastra Pages: 2

Brand: Aastra Pages: 49

Brand: Aastra Pages: 2

Brand: Aastra Pages: 4

Brand: Aastra Pages: 7

Brand: Aastra Pages: 30

Clearspan 6757i

Brand: Aastra Pages: 2

Brand: Aastra Pages: 5

Brand: Aastra Pages: 4

Clearspan 6757i

Brand: Aastra Pages: 2

Brand: Karel Pages: 72

Brand: PhoneMate Pages: 24

Brand: Marco Pages: 3

Brand: Daewoo Pages: 44

Brand: Amplicomms Pages: 50

Brand: Shiro Pages: 23

Brand: Enapter Pages: 30

Brand: VTech Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands