Panasonic VB-44210G User Manual Download Page 200 | Manualshive

Page: 200 / 394

background image

Chapter 4. Key Telephone Features

Section 700 - Operation

4-84

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Considerations

• To make an Intercom Call, press the FF key programmed as an intercom

key and then dial the extension number.

• If a member of the trunk group assigned to FF1 is also assigned to a Direct

Line key, Prime Line Pickup will access the Direct Line key instead of
FF1.

• Prime line preference should not be assigned to an SLT or DSLT

telephone.

Private Line

(All Versions)

Description

An outside line can be reserved for exclusive access by one extension,
eliminating the need for the extension user to wait for a free outside line
during busy periods.

Operation

1. Press the CO line key designated as a Private Line.

• The phone issues outside dial tone.

• The line LED lights green.

• “CO TALK #XX” (where “XX” is the line number) appears on the

display.

2. Dial the telephone number.

The number appears on the display.

3. Complete the call and replace the handset.

The line LED goes off.

«
...
198
199
200
201
202
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Jacob Jensen Pages: 32

Brand: Icom Pages: 75

Brand: Pantech Pages: 50

Brand: Teac Pages: 2

Brand: TeachLogic Pages: 28

Brand: Yamaha Pages: 108

W60P Telesystem

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

CP930W Telesystem

Brand: Yealink Pages: 14

Brand: Yealink Pages: 2

SpectraLink 8002 Series

Brand: Polycom Pages: 72

Brand: X-Micro Pages: 57

Brand: TechniSat Pages: 8

Brand: BT Pages: 15

Brand: Innovative Technology Pages: 14

Brand: Salus Pages: 41

Brand: Samson Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands