Panasonic VB-44210G User Manual Download Page 127 | Manualshive

Page: 127 / 394

background image

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-11

Call Forwarding

(All Versions)

Call Forwarding allows users to send their calls to another extension, to an
outside line, or to voice mail. All versions of the DBS provide call
forwarding; however, some call forwarding enhancements are not available
with earlier versions. The following table shows the call forwarding features
available with each release.

Table 4-3. DBS Call Forwarding features

Descriptions

Call Forwarding--All Calls

. When the Call Forwarding--All Calls feature

is activated, all incoming calls to an extension are immediately forwarded.

Call Forwarding--No Answer.

When Call Forwarding--No Answer is

activated, an unanswered call will ring until the Call Forward No Answer
timer expires. When the timer expires, the unanswered call is forwarded.

Call Forwarding--Busy.

When Call Forwarding--Busy is activated, all

incoming calls to a busy extension will be forwarded.

Call Forwarding--Busy/No Answer.

When Call Forwarding--Busy/No

Answer feature is activated, all incoming calls to an extension that is busy or
does not answer will be forwarded.

Feature

Availability

Call Forwarding--All Calls

All versions

Call Forwarding--No Answer

CPC-AII and CPC-B Version 2.0 or higher

Call Forwarding--Busy

All versions

Call Forwarding--Busy/No
Answer

All versions

Call Forwarding--External

CPC-A, CPC-AII prior to 7.0 and CPC-B
prior to 7.0.

(Beginning with CPC-AII/CPC-B Version
7.0, all forwarding types (All Calls, No
Answer, Busy, Busy/No Answer) allow call
forwarding outside - eliminating the need for
the special Call Forwarding - External type
723.)

Permanent Call Forwarding

CPC-AII and CPC-B Version 3.1 or higher

«
...
125
126
127
128
129
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 100

Brand: Uniden Pages: 12

Brand: Samsung Pages: 2

Brand: Barracuda Pages: 3

UltraShift PLUS

Brand: Eaton Pages: 2

Brand: Laser Pages: 3

Brand: Gigaset Pages: 27

Brand: MALUX Pages: 16

Brand: DAPAudio Pages: 36

Brand: Octet Matrix Audio Pages: 14

CXAI 5198 SERIES

Brand: Uniden Pages: 68

Brand: switel Pages: 120

Brand: Serene Pages: 2

Brand: Savannah Pages: 9

Brand: Kodak Pages: 25

Brand: AMC Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands