Panasonic VB-44210G User Manual Download Page 109 | Manualshive

Page: 109 / 394

background image

Section 700 - Operation

Chapter 3. System Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page 3-63

Trunk Queuing

(All Versions)

Description

If all outside lines in a Trunk Group are busy, the system can call you when a
line becomes free. Simply pick up the handset and dial the telephone number
when the Trunk Callback alert tone rings.

Operation

To set Trunk Queuing:

1. Press

the

ON/OFF

key.

2. Press the CO line key or dial a trunk access code.

The phone issues busy tone.

3. Press

“2.”

“In CO Queuing” appears on the display.

4. Press

the

ON/OFF

key.

5. Wait for the Trunk Callback alert tone.

To respond to the Trunk Callback alert tone:

Pick up the handset.

• The outside line is automatically accessed.

• The phone issues dial tone.

• “CO TALK #XX” (where “XX” is the line number) appears on the display.

Related Programming

• FF1 (System): Extension Class of Service Setting

• FF3 (Extension): Extension Class of Service Assignment

«
...
107
108
109
110
111
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Fanstel Pages: 22

Brand: VacPak-It Pages: 9

Yealink SIP-T22P

Brand: Yealink Pages: 2

Brand: Yealink Pages: 3

Brand: Radio Shack Pages: 20

Brand: AT&T Pages: 21

EuroPhone Basic 10

Brand: HAGENUK Pages: 87

TRUE MOBILITY WIRELESS SYSTEM SWM3000

Brand: SABINE Pages: 40

Brand: Rath Pages: 9

Brand: switel Pages: 120

Brand: NEXT pool Pages: 19

Brand: Kogan Pages: 8

Brand: Cansec Pages: 32

Brand: Easydive Pages: 2

Brand: Supersonic Pages: 6

Brand: SAN/BAR Pages: 11

SP5050 - Bluetooth hands-free Speakerphone

Brand: Jabra Pages: 14

Brand: Samson Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands