Panasonic Toughbook CF-F8EWAZZJM Reference Manual Download

Page: 26 / 140

Battery Power

When the AC adaptor is connected.

The orange display light has three modes: on, flashing and blinking. Note the difference between flashing and blinking.

NOTE

Once the battery is fully charged, the computer performs recharging only when the remaining battery power becomes
less than approximately 95% (75% when the battery’s Economy Mode (ECO) is enabled), so overcharging is avoided.

There are three methods to check the remaining battery power.

To check the remaining battery power on the screen

(After logging on to Windows)

Press

To check the remaining battery power and remaining time using the Windows
Battery Meter

(After logging on to Windows)

Click or

on the notification area.

Checking the Remaining Battery Power

Display

Condition
When the battery pack is inserted. (example)

When the battery pack is not inserted.

[ECO] is displayed when the battery’s Economy Mode (ECO) is enabled.

Summary of Contents for Toughbook CF-F8EWAZZJM













































































































































Search results

Summary of Contents for Toughbook CF-F8EWAZZJM

Reviews:

Related manuals for Toughbook CF-F8EWAZZJM

Brands by name

Popular brands

Panasonic Toughbook CF-F8EWAZZJM, Reference Manual

Search results

Summary of Contents for Toughbook CF-F8EWAZZJM

Reviews:

Related manuals for Toughbook CF-F8EWAZZJM

Brands by name

Popular brands