Panasonic Toughbook CF-F8EWAZZJM Reference Manual Download

Page: 107 / 140

107

Setup Utility

Boot Prompt Configuration

Underlined items are the factory presets.

Security Menu

Setup Utility Prompt

• When [Setup Utility Prompt] is set to [Disabled], the message “Press F2 for Setup / F12 for LAN”

is not displayed on [Panasonic] boot screen. However, F2 and F12 will work even if the message
is not displayed.

Disabled
Enabled

Password on boot

Disabled
Enabled

Set Supervisor Password

Enter the sub-menu.

Hard Disk Lock

• Can be changed only when [Set Supervisor Password] is set.

Disabled
Enabled

User Password Protection

No Protection
Protected

Set User Password

• Can be changed only when [Set Supervisor Password] is set.

Enter the sub-menu.

Embedded Security (TPM)

• Only for model that supports TPM
• For information on TPM, refer to the

Installation Manual

of “Trusted Platform Module (TPM)”.

Click

(Start), input “c:\util\drivers\tpm\readme.pdf” in [Start Search], and press

Enter

Enter the sub-menu.

Fingerprint Security

• Only for model with Fingerprint Reader

Enter the sub-menu.

AMT Configuration

• Only for model that supports AMT

Enter the sub-menu.

Summary of Contents for Toughbook CF-F8EWAZZJM













































































































































Search results

Summary of Contents for Toughbook CF-F8EWAZZJM

Reviews:

Related manuals for Toughbook CF-F8EWAZZJM

Brands by name

Popular brands

Panasonic Toughbook CF-F8EWAZZJM, Reference Manual

Search results

Summary of Contents for Toughbook CF-F8EWAZZJM

Reviews:

Related manuals for Toughbook CF-F8EWAZZJM

Brands by name

Popular brands