Panasonic TK-AS66-ZEX Page 49 Instruction Manual Download

Page: 49 / 52

EN49

Engli



When there is a water leak

Place where the water leaks

Check following point

Reference

page

Area where the bypass
selector is connected



Has the bypass selector been installed on the faucet securely?



If not, install it securely.

EN10

EN12



Have the parts inside the bypass selector been inserted
properly?



If not, insert them properly.

EN34

Area where the water supply
hose is connected



Has the water supply hose been connected securely to the
bypass selector?



Insert the hose as far as it will go, and tighten it using the
hose fastening nut.

EN14

Area where the outlet pipe
is connected



Has the outlet pipe been connected to the unit securely?



If not, screw it in securely until it will go no further.



Did you install the gasket? Or is the gasket twisted?



Install the gasket properly.

EN15

Top of the unit



Has the cap been installed securely on the unit?

EN39

Bottom of the unit



Has the cartridge been installed securely?



If not, install it securely.



Depending on the temperature and humidity conditions, water
formed from condensation may collect inside the unit.
(This is not a malfunction.)

EN37

EN38

Faucet area



Is the faucet gasket old?



Call in a plumber.



Is the faucet (insulating cap, etc.) cracked?



Call in a plumber.

–

Optional Accessories

Obtain all optional accessories from your dealer.
For details on how they are used, refer to the accompanying instructions.

Consumables

Replacement cartridge

Model No.: TK-AS45C1-EX

For use with large faucet

Large-diameter Faucet Fitting (inside diameter 32.5 mm)

Model No.: P-06JRC



For faucets whose end diameter is 24 ~ 32 mm

Wall mounting bracket

Model No.:
P-A3303ZEX

Used when
mounting the unit
on a wall

CAUTION



If you want to install the unit on a wall, ask an authorised
dealer or service personnel to do the job.

Installing the unit yourself may cause the unit to fall and result in an accident.



The location where the unit is to be installed must be able
to support a weight of over 6 k

If the installation location does not have enough strength to
support the unit, the Alkaline Ionizer may fall, resulting in an
accident and kitchen damage.

TK-AS66-ZEX̲En.indb 49

2017/01/30 15:04:26

Summary of Contents for TK-AS66-ZEX





















































Search results

Summary of Contents for TK-AS66-ZEX

Reviews:

Related manuals for TK-AS66-ZEX

Brands by name

Popular brands

Panasonic TK-AS66-ZEX, Instruction Manual

Search results

Summary of Contents for TK-AS66-ZEX

Reviews:

Related manuals for TK-AS66-ZEX

Brands by name

Popular brands