Panasonic T-Mobile KX-HDV130 Administrator'S Manual Download Page 266

Page: 266 / 332

Description

Specifies the initial delay, in 10-millisecond units, of the jitter buffer.

Value Range

1–7 (

10 ms)

Note

•

This setting is subject to the following conditions:

–

This value must be greater than or equal to "

MIN_DELAY

–

This value must be less than "

MAX_DELAY

Default Value

RTP_PORT_MIN

Value Format

INTEGER

Description

Specifies the lowest port number that the unit will use for RTP packets.

Value Range

1024–59598 (only even)

Default Value

16384

Web User Interface Reference

Minimum RTP Port Number (Page 127)

RTP_PORT_MAX

Value Format

INTEGER

Description

Specifies the highest port number that the unit will use for RTP packets.

Value Range

1424–59998 (only even)

Default Value

32766

Web User Interface Reference

Maximum RTP Port Number (Page 128)

RTP_PTIME

Value Format

INTEGER

Description

Specifies the interval, in milliseconds, between transmissions of RTP
packets.

Value Range

•

Default Value

Web User Interface Reference

RTP Packet Time (Page 127)

266

Administrator Guide

Document Version 2015-12

5.3.26 RTP/RTCP/RTCP-XR Settings

Summary of Contents for T-Mobile KX-HDV130













































































































































































































































































































































Search results

Summary of Contents for T-Mobile KX-HDV130

Reviews:

Related manuals for T-Mobile KX-HDV130

Brands by name

Popular brands

Panasonic T-Mobile KX-HDV130, Administrator'S Manual

Search results

Summary of Contents for T-Mobile KX-HDV130

Reviews:

Related manuals for T-Mobile KX-HDV130

Brands by name

Popular brands