Panasonic Section 700 User Manual Download | Manualshive

Page: 266 / 394

background image

Chapter 6. SLT Features

Section 700 - Operation

6-10

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Call Hold

(All Versions)

Description

Call Hold provides either exclusive or system hold, depending on system
programming. With Exclusive Hold, only the extension that held the call can
retrieve it. With System Hold, another extension can retrieve the call.

Operation

To place a call on Hold:

Flash the switchhook.

To release the call:

Flash the switchhook again.

Related Programming

• FF1 (System): Recall Timer for Extension-Held CO Calls

• FF1 (System): Recall Timer for Extension-Held Intercom Calls

• FF1 (System): SLT Onhook Flash Timer

• FF3 (Extensions): Single Line Telephone Hookflash (Broker’s Hold/

Conference)

• FF1 (System): Single Line Telephone Flash Control

Considerations

• A held call recalls if it is not retrieved before the Hold Recall Timer

expires.

• If there is no response to the Hold Recall, the call transfers to the Attendant

Phone; however, no tone sounds at an Attendant Phone if Night Mode is
activated.

• If you flash the switchhook during a conference call, the flash is ignored.

• If your system is set to onhook transfer, and you have placed an outside

call on hold and then made an intercom call, make sure the other extension

«
...
264
265
266
267
268
...
»

Summary of Contents for Section 700











































































































































































































































































































































































































Reviews:

No comments

Related manuals for Section 700

Brand: TCL Pages: 22

Brand: i.safe MOBILE Pages: 21

Brand: TCL Pages: 34

Brand: TCL Pages: 38

Brand: TCL Pages: 26

Brand: TCL Pages: 10

Brand: palmOne Pages: 2

Brand: Barracuda Pages: 4

Grandstream GXP-2010

Brand: Grandstream Networks Pages: 1

ClearSky TVP-SP1BK

Brand: TRENDnet Pages: 13

Brand: TCM Mobile Pages: 37

HTC Incredible S

Brand: HTC Pages: 78

Brand: T-Mobile Pages: 43

DROID DROID INCREDIBLE

Brand: HTC Pages: 206

Brand: Nordmende Pages: 40

Brand: Uniden Pages: 44

Brand: Flyingvoice Pages: 51

Instinct HD SPH-M850

Brand: Samsung Pages: 242

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands