Panasonic Section 700 User Manual Download

Page: 110 / 394

Chapter 3. System Features

Section 700 - Operation

Page 3-64

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Considerations

• Response to the Trunk Callback alert tone must be within sixteen seconds

or Trunk Queuing will be canceled.

• If a call arrives from an outside line while the Trunk Queuing feature is

activated, Trunk Queuing will be suspended for the duration of the
incoming call.

• If you are engaged in another call on a different line for more than twenty

minutes after the desired outside line becomes available, that outside line’s
assignment to you will be canceled.

• The Trunk Queuing feature may also be used if you hear a busy tone when

trying to make a call using the Pooled Trunk Access feature.

• Trunk Queuing can be used by all telephone types including SLTs and

DSLTs.

Universal Night Answer

(All Versions)

Description

During night mode, Universal Night Answer (UNA) sends incoming calls to
an external ringer, such as a night bell.

As an alternative to using a night bell, UNA can also be configured to ring
external paging speakers.

Universal Night Answer calls can be picked up from any extension, provided
the extension’s Class of Service allows UNA answer.

Operation

To answer a UNA call:

1. Pick up the handset.

The phone issues intercom dial tone.

2. Dial

“78.”

“CO TALK #XX” appears on the display (where “XX” = the trunk
number).

Summary of Contents for Section 700











































































































































































































































































































































































































Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands

Panasonic Section 700, User Manual

Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands