manualshive.com logo in svg

Panasonic Section 700, Technical Manual

Share
Download
Panasonic Section 700 Technical Manual Download Page 262

262

ICX (International), issued March/1999

ICX-35-700

Chapter 7. SLT Features

Section 700 - Operation

Hardware Requirements

•

A Call Logging printer or external call accounting system is required to collect account code 
records.

Considerations

•

Account codes are not available during conversation recording mode for the Built-In Voice Mail.

•

Even though up to 10 digits may be entered, the system verifies the ID based on the first 4 digits 
only.

•

Account codes will be cancelled after using trunk queuing.-

•

Account codes are not available for a Dial Pulse SLT.

•

SLT telephones can only use account codes with outgoing calls only.

•

Account Codes interact with TRS (Call Barring) as shown in the following table:

Attendant Group Calls

CPC-96, CPC-288, and CPC-576 All Versions

Description

You can call the attendant group from any extension by dialling the designated attendant number.

5.   Enter trunk access code (default = 9 [UK/HK], 0 [Taiwan, 

Malaysia, Indonesia], or 81-84).

6.   Dial the phone number.

Forced or Not Forced

Verified or 

Non-Verified

TRS (Call Barring) Class

No Account Entry

Account Entry

Not Forced

Non-Verified

Extension Port Based TRS 

Class

Extension Port Based TRS 

(Call Barring) Class

Verified

Account Code Based TRS 

(Call Barring) Class

Forced

Non-Verified

TRS (Call Barring) Class 

for Forced Account Code 

(FF1 0 19 0001)

Extension Port Based TRS 

(Call Barring) Class

Verified

Account Code Based TRS 

(Call Barring) Class

Action

Result

Summary of Contents for Section 700
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands