Panasonic SC-HG1-C User Manual Download Page 84

Page: 84 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-50

4-10-3 Command sending procedure

Use this procedure to select a destination controller and send a command once only to that

controller.

There is a slight difference in the operation of read commands and write commands.

<Read command sending procedure>

This section explains the procedure for using the command transmission function to read con-

troller information.

The example of sending the get judgment value command “0x0010” (Read) to a master unit

and slave units 1 to 3 is shown below.

is only set when the operation mode is CC-Link

mode 1.

0x0000

0x00000000

RX[7B] (*1)

Check remote ready flag

RX[0C]

Check command flag

RY[0C]

Command flag

RWw[00]

Set command request

sensor

RY[01]

Write flag

RWw[01]

Set command code
RY[00]

Send request flag

RY[10]

Page 1 settings

RX[00]

Check send done flag

RX[10]

Check page 1 settings

0x000F

0x0010

RWr[01]

Check command

response code

RWr[00]

Check command

response sensor

RWr[02] to [09]

Check sensor response data

0x000F

0x0010

Detected value (master unit + 3 slave units)

Read mode

RX[7A] (*2)

Check error status flag

RX[01]

Check error flag

When operation mode is CC-Link mode 1

Summary of Contents for SC-HG1-C

































































































































Search results

Summary of Contents for SC-HG1-C

Reviews:

Panasonic SC-HG1-C, User Manual, Page: 84 / 128

Search results

Summary of Contents for SC-HG1-C

Reviews: