manualshive.com logo in svg

Panasonic SC-HG1-C, User Manual, Page: 123 / 128

Share
Download
Panasonic SC-HG1-C User Manual Download Page 123

Troubleshooting

WUME-SCHG1C-4

8-7

8-4 What to do when a problem occurs

■ Power indicator (Green) is not lit

Cause

Solution

Power is not supplied.

Check if the capacity of the power supply is sufficient.

Connect the power supply correctly.

The power supply voltage is not within the 

specifications.

Correctly set the power supply voltage.

A connector for connection to a controller is not 

firmly connected.

Firmly connect the connector.

■L_ERR indicator (RED) is lit or blinking

State

Cause

Solution

ON

An out-of-range station number was 

set when the power was turned on.

Check if the switch type setting is correct.

Cycle the power OFF - ON.

Blinking The switch type setting was changed 

after the power was turned on.

Change the switch type setting to the setting that was in effect 

before the power was turned on.

To apply a change, cycle the power OFF - ON.

■ ERR indicator (RED) is lit or blinking

State

Cause

Solution

ON

CC-Link communication has been inter-

rupted.

Check if the CC-Link connectors are correctly connected.

Connect correctly.

CC-Link data link has failed.

Check if the parameter settings and switch type setting are 

correct.

Cycle the power OFF - ON.

Blinking Communication between controllers is 

not taking place normally.

Check the connection of connected units.

Cycle the power OFF - ON.

<Important>

If the product still does not operate normally after you check the above, consult our technical sup-

port center.

Summary of Contents for SC-HG1-C

































































































































Reviews:

No comments