Panasonic SC-HG1-C User Manual Download Page 118

Page: 118 / 128

Troubleshooting

WUME-SCHG1C-4

8-2

Solutions to frequently encountered problems and errors are described below.

8-1 Command error

A command error will occur in response to a sent command if the command setting is outside

the range. Check the error code and take appropriate action.

The example of an out-of-range parameter error in slave unit 2 when the LOW set value com-

mand "0x0014" (write) is sent to a master unit and slave units 1 to 3 is given below.

only set when the operation mode is CC-Link mode 1.

For error codes and solutions, refer to “<Table of error codes>”.

RX[7B] (*1)

Check remote ready flag

RWr[6][7]

Check error code

RWr[2] to [5], [8], [9]

Check sensor response data

RY[00]

Send request flag

RX[01]

Check error flag

RX[00]

Check send done flag

RX[60] to [6F]

Error output flag

0x0004 (bit of 2nd slave unit is set)

0x0000

RWr[1]

Check command response code

RWr[0]

Check command response

sensor

0x000F

0x0000

0x0014

0x0000

Out-of-range parameter error occurred in 2nd slave unit

RX[7A] (*2)

Check error status flag

0x00000065 (error code)

0x0000

RY[10]

Page 1 settings

RX[10]

Check page 1 settings

When operation mode is CC-Link mode 1

RX[0C]

Check command flag

RY[0C]

Command flag

RY[01]

Write flag

Write mode

RWw[00]

Set command request sensor

RWw[01]

Set command code

0x000F

0x0014

RWw[02] to [09]

Set command data

LOW set value (master unit + 3 slave units)

0x00000000

Summary of Contents for SC-HG1-C

































































































































Search results

Summary of Contents for SC-HG1-C

Reviews:

Panasonic SC-HG1-C, User Manual, Page: 118 / 128

Search results

Summary of Contents for SC-HG1-C

Reviews: