Panasonic PX380G-BS300, Operating Instructions Manual

Page: 170 / 229

– 170 –
Chapter 8 Display — Screen status display
f [END]*
1
: Displayed when combining of clips is ended in one-clip recording.
f [L-]*
2
: Loop recording
f [I-]*
2
: Interval recording, one-shot recording
f [P-]*
2
: Pre-recording
*1 Even if the display is set to [OFF], only [REC], [START], and [END] are displayed. Also, when pre-recording, loop recording, interval recording, or one-shot
recording is set, it is displayed.
*2 Displayed when [INTERVAL], [ONE SHOT], or [LOOP] is set in the main menu → [RECORDING SETUP] → [RECORDING], or when [ON] is set in the
main menu → [RECORDING SETUP] → [PRE REC].
42 Rec during upload status and streaming distribution status display
Displays the status of rec during upload.
f [ ]: Displayed when the rec during upload function is enabled.
The display will blink when recording is started immediately after the power is turned on or the P2 card is inserted, and the upload will not be
performed until the recording is stopped.
f [ ]: Displayed during upload.
f [ ]: Displayed from when transfer error occurred during upload until when the next upload starts.
Displays the streaming status.
f [ ] (blinking): Blinks while the camera is being connected to a device which will receive the streaming video.
f [ ] (illuminated): Displayed when the camera is connected to a device receiving the streaming video and the camera is transmitting streaming
video.
The display turns off when a connection could not be established properly.
@ @
NOTE
t Depending on the network status, the [ ] display may not be able to follow during actual operation.
43 High-sensitivity mode display
Displayed when [HIGH SENS.] is set in the main menu → [SYSTEM MODE] → [SHOOTING MODE].
44 4G/LTE connection status and the bonding device status display
Displays the 4G/LTE connection status. Displays at the 4G/LTE connection. Displays the strength of the signal reception in six levels. Displays the
radio wave strength with the number of vertical bars. It is not displayed when the setting of 4G/LTE is disabled.
f [4G/LTE ]: During 4G/LTE connection
f [4G/LTE ]: When not connected with4G/LTE
f [4G/LTE ]: When there is a problem with the 4G/LTE connection
Displays the bonding device status. Displays the device status received from the bonding device. Displays the strength of the signal reception of the
bonding device in six levels, and remaining battery in six levels. [E] is displayed when there is an error in the bonding device.
@ @
NOTE
t Depending on the USB modem that is supported, vertical bars that indicate the signal strength may not be displayed.
t The device status may not be acquired depending on the connected bonding device.
t For details on bonding device that the camera can acquire the device status, visit the support desk at the following website:
https://pro-av.panasonic.net/
45 HD SDI REMOTE recording status display
Displays the control status of whether recording has started or stopped for an external device which is connected to the <SDI OUT1> terminal.
When [ON] is set in the main menu
→ [IN/OUT SEL] → [HD SDI REMOTE], the status will always be displayed regardless of the setting in the main
menu → [DISPLAY SETUP].
f [SDI n ]: Status where the recording is being instructed for an external device
f [SDI & ]: Status where recording stop is being instructed for an external device
Camera status display
These are indicated in the information display area in the center.
[ABB]: Displayed while automatic black balance operation is active.
[ATW MODE]: Displayed when the <AUTO W/B BAL> switch is pushed to the <AWB> side while auto tracking white balance is active. This is also
displayed when the <WHITE BAL> switch is turned to <B> if [ATW] is allocated.
[AWB]: Displayed while automatic white balance operation is active.
[WHITE:PRE
**** K]: Displays the set color temperature when the <WHITE BAL> switch is switched.
[AWB PRESET **** K]: Displayed when the <WHITE BAL> was set to <PRST> in an attempt to execute automatic white balancing.
[BACK LIGHT]: Displayed when pressing the USER button to which [BACKLIGHT] is allocated for iris control, and switching the status.
[GAIN
** dB]: Displayed when gain is switched.
[SHUTTER 1/ **** ]/[SHUTTER OFF]: Displayed when you switch the shutter speed.
[SPOT LIGHT]: Displayed when pressing the USER button to which [SPOTLIGHT] is allocated for iris control, and switching the status.
Checking and displaying the shooting status
Also, the mode check [STATUS] screen is displayed when the <DISP/MODE CHK> switch is pushed towards the <CHK> side. During mode check,
almost all items are displayed including usually hidden items so that the shooting status can be checked. For details on the mode check, refer to “Mode
check display” (page 172).
The list shows the display/hide status of each item in the [STATUS] screen. The display/hide status differ depending on the <DISP/MODE CHK> switch
settings and settings in the main menu
→ [DISPLAY SETUP] → [OTHER DISPLAY].
f “ l ” indicates displaying, and “—” indicates hiding.
f [ON]/[OFF] for each item can be selected in the main menu → [DISPLAY SETUP] → [DISPLAY SETTING].