Panasonic PV-500, User Manual, Page: 371 / 494

369
O
pe
ra
tio
n a
n
d D
a
ta
O
ut
put
t
hr
ou
gh I
/O
T
e
rm
ina
ls
C
h
ap
te
r 8
INDE
X
ASSIGN 0 - 5 (ASN0-5): Function Assignment (* partly)
Use this signal to perform the function shown in the table below by a signal from the external device.
To assign a function to Assign signal, select “ENVIRONMENT” > “Input/Output” > “Parallel I/O” in SETUP
menu.
Template Setting (*): The same as REENTRY
Switch Run/Stop: The same as RUN/STOP
Save Data in PV (*): All product type data currently registered in “execution memory” will be
saved in “memory for store” of PV. Specify a storing area number (0 - 99)
with “IN0 - IN6”.
Save Data in SD (*): All product type data currently registered in “execution memory” will be
saved in a SD memory card. Specify a storing area number (0 - 99) with
“IN0 - IN6”.
Read Data from PV (*): The setting data registered in the storage space in PV500 will be called
up to “execution memory”. Specify a reading area number (0 - 99) with
“IN0 - IN6”.
Read Data from SD (*): The product type data registered in a SD memory card will be called up to
“execution memory” of PV.
Reinspect:
Input this to reinspect without capturing an image. Enter a block number
(0 - 9) to execute with “IN0 - IN3”.
Reset Statistics (*): Input this to clear the statistics data and scan count.
Reset Error (*): ERROR 0 and ERROR 1 will be turned off.
Save Image Memory in SD (*):
Backs up all images saved in the image memory to a SD memory card.
Creates a folder named one of "00" to "99" which does not exist in
"Panasonic MEW VIsion¥PV500¥Image¥Backup" in a SD memory card
and saves images in the folder.
Output Latest Image(*): Outputs the latest inspection image.
The destination (SD memory card or PC connected with Ethernet cable)
and the file name can be set from "ENVIRONMENT" > "Input/Output" >
"Image Output" menu.
• In "ENVIRONMENT" > "Input/Output" > "Image Output", set
"Output Conditions" to "Command Reception".
• Image Receiver needs to be activated on the destination PC when
"Destination" is set to "Ethernet".
Clear Image Memory (*):
All image data registered in the Storage Space in PV500 will be cleared.
Print Screen (*): The currently displayed screen (entire contents the monitor displaying)
will be captured and saved in a SD memory card or a PC through
Ethernet.
You can specify destination from “ENVIRONMENT” > “Input/Output” >
“Print Screen”
.
Abort Inspection/Process Cancels the following active operations, and restores into the previous
status before the operation.
• Cancellation of the operation of a serial command which has been
received
• Abort of the status waiting for Individual trigger input
• Abort of output in the status waiting for result output after an
inspection is complete
• Abort of image saving from Image Memory to a SD memory card
• Cancellation of template re-registration
Abort Save/read Setting Data
Cancels saving or reading the setting data.
IN0 - 15: Input data
These are signals to input the values for switching type, reading/saving setting data when you execute the
functions. Specify values in binary data as follows.
Example 1) Specifying No.6
IN7 IN6 IN5 IN4 IN3 IN2 IN1 IN0
0 0 0 0 0 1 1 0
Example 2) Specifying No.237
IN7 IN6 IN5 IN4 IN3 IN2 IN1 IN0
1 1 1 0 1 1 0 1