Panasonic PT-MZ670 Operating Instructions Manual Download Page 154

Page: 154 / 228

Chapter 5

Operations — Network connection

154 - ENGLISH

Connecting via wired LAN

This projector can receive the Ethernet signal from the twisted-pair-cable transmitter together with the video,

audio, and serial control signal via a LAN cable.

Example of a normal network connection

Computer

Projector

LAN cable (straight)

Hub

Attention

When a LAN cable is directly connected to the projector, the network connection must be made indoors.

Note

A LAN cable is required to use the network function via wired LAN.

Connect a LAN cable to send and receive the Ethernet signal to the <LAN> terminal or the <DIGITAL LINK/LAN> terminal of the projector.

Use a straight or crossover LAN cable that is compatible with CAT5 or higher. Either the straight or the crossover cable, or both cables

can be used depending on the system configuration. Consult your network administrator. The projector will determine the type of the cable

(straight or crossover) automatically.

Use a LAN cable of 100 m (328'1") or shorter.

Example of network connections via a twisted-pair-cable transmitter

Computer

Projector

LAN cable (straight)

Twisted-pair-cable transmitter

Hub

Attention

When a LAN cable is directly connected to the projector, the network connection must be made indoors.

Note

For the LAN cable between the twisted-pair-cable transmitter and the projector, use a cable that meets the following criteria:

Conforming to CAT5e or higher standards

Shielded type (including connectors)

Straight-through

Single wire

The maximum transmission distance between the twisted-pair-cable transmitter and the projector is 100 m (328'1"). It is possible to transmit

up to 150 m (492'2") if the twisted-pair-cable transmitter supports the long-reach communication method. However, the signal that the

projector can receive is only up to 1080/60p (1 920 x 1 080 dots, dot clock frequency 148.5 MHz) for the long-reach communication method.

If this distance is exceeded, image may be disrupted or a malfunction may occur in LAN communication.

Summary of Contents for PT-MZ670





































































































































































































































Search results

Summary of Contents for PT-MZ670

Reviews:

Panasonic PT-MZ670, Operating Instructions Manual, Page: 154 / 228

Search results

Summary of Contents for PT-MZ670

Reviews: