Panasonic PT-DS100XE ( ), Operating Instructions Manual

Page: 58 / 130

PICTURE menu
58
- ENGLISH
Settings
SYSTEM SELECTOR
This enables the projector to automatically recognize
input signals. Furthermore, if unstable signals are
input, the system format can be selected manually.
Press ▲▼ to select [SYSTEM 1 )
SELECTOR].
Press <ENTER> button.
2 )
Press ▲▼ to switch [SYSTEM 3 )
SELECTOR].
Press <ENTER> button.
4 )
VIDEO/S-VIDEO terminal input
J
signal
Select from AUTO, NTSC, NTSC4.43, PAL,
PAL-M, PAL-N, SECAM, and PAL60.
Attention
[AUTO] mode is selected by default.
z
When the projector is not working properly in [AUTO]
z
mode, change the setting according to each SYSTEM
SELECTOR type.
Note
[AUTO] automatically selects from NTSC, NTSC4.43,
z
PAL, PAL-M, PAL-N, SECAM, and PAL60.
RGB1/RGB2 terminal input signal
J
480i, 576i, 576p signals
z
Select from RGB and YC
B
C
R
.
VGA60, 480p signals
z
Select from VGA60, 480p, and 480pRGB.
Other signals
z
Select from RGB and YP
B
P
R
.
Note
Refer to
z
“List of compatible signals” ( Æ page 123) for
available signals.
DVI-D terminal input signal
J
480p, 576p signals
z
Select from RGB and YC
B
C
R
.
Other signals
z
Select from RGB and YP
B
P
R
.
Note
Refer to
z
“List of compatible signals” ( Æ page 123) for
available signals.
Malfunction may occur or other problems could be
z
encountered with some equipment.
HDMI terminal input signal
J
480p, 576p signals
z
Select from Auto, RGB, and YC
B
C
R
.
Other signals
z
Select from Auto, RGB, and YP
B
P
R
Note
Refer to
z
“List of compatible signals” ( Æ page 123) for
available signals.
Malfunction may occur or other problems could be
z
encountered with some equipment.
SDI terminal input signal
J
(PT-DZ110XE/PT-DS100XE only)
Select from AUTO, 1 080/60i, 1 035/60i,
z
720/60p, 1 080/24p, 1 080/50i, 1 080/30p,
1 080/25p, 1 080/24sF, 720/50p, 480i, and 576i.
Refer to
z
“List of compatible signals”
(
Æ
page 123) for available signals.
To display pictures complying
with the sRGB standard
sRGB is the international color reproduction standard
(IEC61966-2-1) established by IEC (International
Electrotechnical Commission).
To reproduce colors more faithfully in compliance
with the sRGB standard, perform the following setting
procedure.
Set [COLOR MATCHING] adjustment to 1 )
[OFF].
Refer to “COLOR MATCHING”
z
(
Æ
page 69).
Display the [PICTURE] screen. 2 )
Refer to
z
“PICTURE menu” ( Æ page 53).
Press ▲▼ to select [PICTURE MODE]. 3 )
Press ◄► to select [NATURAL]. 4 )
Press ▲▼ to select [COLOR]. 5 )
Press <DEFAULT> button on the 6 )
remote control to restore the factory
default.
Follow the same procedure (steps
7 )
5-6) to restore the factory default for
[TINT], [COLOR TEMPERATURE] and
[GAMMA].
Note
sRGB is only enable when RGB signals are being input.
z