Panasonic PAW-VP1000LDHW Installation Manual Download Page 61

Page: 61 / 88

DHW PAW-VP - Installation manual – 2020-05

How to make Settings

8.1.4 Detailed settings for indoor/outdoor unit CZ-RTC5B/RTC4/2

The new value must be set during the commissioning.

8.1.5 Setting Flow Chart

The system is in a fault-free state so that a safe commissioning can take place. All valid rules

have been followed.

Important

To follow exactly the described steps at the following flow chart is mandatory.

No.

Action

Note

Check if all temperature sensors are correctly

connected. All jumpers/bridged plugs (if any)

according to the wiring diagram, power supply and

communication wires are connected as shown in the

electrical wiring diagram.

Wait until initialization is finished.

Described at pages before:

Setting Procedure for Remote Controller Model

CZ-RTC5B

Attention:

After the setting "DN" 10 & 11 go out of detailed

setting:

Follow described at pages before:

Setting Procedure for Remote Controller Mode

CZ-RTC5B

See corresponding "DN" code list described on the

following pages, (combination for combination) for

Indoor Unit.

Described at pages before:

Setting Procedure for Remote Controller Model

CZ-RTC5B

Wait until initialization is finished.

Described at pages before: Detailed Setting Procedure

for Remote Controller Model CZ-RTC2 / CZ-RTC4

See corresponding "DN" code list described on the

following pages (combination for combination) for

Outdoor unit.

Described at pages before: Detailed Setting Procedure

for Remote Controller Model CZ-RTC2 / CZ-RTC4

After restart Power supply and Initialisation is finished,

proceed commissioning.

Check Indoor Unit

Turn Power “ON”

Start Indoor Unit Detail Setting

Set Indoor Unit

"DN" code 10 & 11

Start Outdoor Unit Detail Setting

Restart Detail Setting and set

other Indoor Unit "DN" codes

Set Outdoor Unit "DN" codes

Finish Indoor Unit

"DN" code setting

Finish Outdoor unit

"DN" code setting

Reset Power supply

Initialization

Summary of Contents for PAW-VP1000LDHW

























































































Search results

Summary of Contents for PAW-VP1000LDHW

Reviews:

Related manuals for PAW-VP1000LDHW

Brands by name

Popular brands

Panasonic PAW-VP1000LDHW, Installation Manual

Search results

Summary of Contents for PAW-VP1000LDHW

Reviews:

Related manuals for PAW-VP1000LDHW

Brands by name

Popular brands